Minicom komunicira, wvdial neMinicom se uspije po vezati na mobitel, i mogu mu slati komande, ali wvdial, koji u konačnici želim koristiti, ne želi komunicirati.
U čemu je problem?
Screenshot minicoma uspješno povezanog:
Dio config fajla wvdial-a:
Code:
[Dialer Defaults]
FlowControl = NOFLOW
Modem = /dev/ttyUSB0
Baud = 115200
SetVolume = 0
Dial Command = ATDT
#Init1 = AT+cbst=71,0,1
Init2 = ATZ
Init3 = ATM0
[Dialer Defaults]
FlowControl = NOFLOW
Modem = /dev/ttyUSB0
Baud = 115200
SetVolume = 0
Dial Command = ATDT
#Init1 = AT+cbst=71,0,1
Init2 = ATZ
Init3 = ATM0
Izlaz nakon pokretanja wvdiala:
Citat:
$ wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
--> Sending: ATQ0
--> Re-Sending: ATZ
--> Modem not responding.
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
--> Sending: ATQ0
--> Re-Sending: ATZ
--> Modem not responding.
Izlaz wvdialconf:
Citat:
sudo wvdialconf
[sudo] password for marko:
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
Modem Port Scan<*1>: S0 S1 S2 S3
ttyACM0<Info>: Device or resource busy
Modem Port Scan<*1>: ACM0
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
Please read the FAQ at http://open.nit.ca/wiki/?WvDial
If you still have problems, send mail to <[email protected]>.
[sudo] password for marko:
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
Modem Port Scan<*1>: S0 S1 S2 S3
ttyACM0<Info>: Device or resource busy
Modem Port Scan<*1>: ACM0
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
Please read the FAQ at http://open.nit.ca/wiki/?WvDial
If you still have problems, send mail to <[email protected]>.
Zahvaljujem!
http://www.dropbox.com/referrals/NTQ0MTI2NDc5
https://www.agronomija.info/
Failure is not an option. It comes bundled with your Microsoft product.
https://www.agronomija.info/
Failure is not an option. It comes bundled with your Microsoft product.
