[es] - Usb hub 2.0 problem

Stator
System Administrator
Beograd

Član broj: 14552
Poruke: 257
*.ADSL.neobee.net.

+3 Profil

^{29.04.2006. u 13:28 - pre 218 meseci}

Upravao sam kupio no name usb hub sa 4 porta. Na Windows-u mi radi super dok me na Linux-u malko zeki :)

Code:

stator@bender ~ $ uname -a
Linux bender 2.6.15-gentoo-r7 #7 Fri Apr 28 16:43:36 CEST 2006 x86_64 AMD Athlon(tm) 64 Processor 3200+ GNU/Linux

Kada ga utaknem, dmesg mi izbaci ovo, znaci prepoznan je od strane kernela

Code:

usb 1-1: new high speed USB device using ehci_hcd and address 13
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected

Ona ubacim moj usb disk koji inace super radi kada se direktno utakne i dmesg kaze ovo

Code:

ehci_hcd 0000:00:02.1: qh ffff81003f9c51e0 (#00) state 4
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 14
usb-storage: waiting for device to settle before scanning
Vendor: CORNICE Model: Inc. Storage Ele Rev: 042R
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 2858688 512-byte hdwr sectors (1464 MB)
sdb: assuming drive cache: write through
SCSI device sdb: 2858688 512-byte hdwr sectors (1464 MB)
sdb: assuming drive cache: write through
sdb: sdb1
sd 8:0:0:0: Attached scsi disk sdb
usb-storage: device scan complete

E sada ide onaj zabavni deo, kada ga mountujem i pokusam da mu pristupim jednostavno on pokaze da je prazan

Code:

hub 1-1:1.0: cannot reset port 3 (err = -71)
hub 1-1:1.0: hub_port_status failed (err = -71)
hub 1-1:1.0: cannot reset port 3 (err = -71)
hub 1-1:1.0: cannot reset port 3 (err = -71)
hub 1-1:1.0: cannot reset port 3 (err = -71)
hub 1-1:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 1-1:1.0: cannot disable port 3 (err = -110)
hub 1-1:1.0: cannot reset port 3 (err = -110)
hub 1-1:1.0: cannot reset port 3 (err = -110)
hub 1-1:1.0: cannot reset port 3 (err = -110)

I gomila ovakvih gresaka (c/p sam sam jedan mali deo)

Code:

end_request: I/O error, dev sdb, sector 2446368
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446369
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446370
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446343
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446343
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446423
end_request: I/O error, dev sdb, sector 2446424
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446423
FAT: Directory bread(block 2446360) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446424
FAT: Directory bread(block 2446361) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446425
FAT: Directory bread(block 2446362) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446426
FAT: Directory bread(block 2446363) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446427
FAT: Directory bread(block 2446364) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446428
FAT: Directory bread(block 2446365) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446429
FAT: Directory bread(block 2446366) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446430
FAT: Directory bread(block 2446367) failed
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 796
FAT: FAT read failed (blocknr 733)
hub 1-1:1.0: hub_port_status failed (err = -110)
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 5639
printk: 38 messages suppressed.
Buffer I/O error on device sdb1, logical block 5576
lost page write due to I/O error on sdb1
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 5640
Buffer I/O error on device sdb1, logical block 5577
lost page write due to I/O error on sdb1
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2102791
Buffer I/O error on device sdb1, logical block 2102728
lost page write due to I/O error on sdb1
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2446327
Buffer I/O error on device sdb1, logical block 2446264
lost page write due to I/O error on sdb1
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2102791
sd 8:0:0:0: SCSI error: return code = 0x70000
end_request: I/O error, dev sdb, sector 2102791
FAT: Directory bread(block 2102728) failed

Jos jedanput napominjem da mi pod win-om radi bez greske?
Ima li neko ideju sta da radim?

Odgovor na temu