[es] - Suse 9.3 x64 UDMA5

Wakizashi
Novi Beograd

Član broj: 1451
Poruke: 14
*.adsl.sezampro.yu.

Profil

^{21.06.2005. u 09:47 - pre 242 meseci}

Poz,
prvo nisam neki linux fanatik, pa bih zamolio da flame ostavite za neku drugu priliku, a savete o vec pisanim tekstovima na temu da date u formatu "imas na forumu www.svezalinux.com", vec sam trazio po ostalim forumima, ali pored "do You have 80pin cable" nisam nasao nista pametno :)
Dakle, racunar je Amilo A 1630 notebook, Amd 64, Sis chipset, HDD Toshiba MK6021GAS. HDD windoze uredno prijavljuje kao UDMA 5 tako da kabl problem otpada.
hdparm -i /dev/hda daje sledece

/dev/hda:

Model=TOSHIBA MK6021GAS, FwRev=GA024A, SerialNo=34470590S
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117210240
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

hdparm -d1 -X69 /dev/hda daje
/dev/hda:
setting using_dma to 1 (on)
setting xfermode to 69 (UltraDMA mode5)
using_dma = 1 (on)

ALI ne prebacuje na UDMA 5 nego -i opet daje udma2
Zaboravih da napisem da je kernel 2.6.11.4-21.7-default
Da li neko ima neki savet kako da ovo resim, i ukoliko ukljucuje kompajliranje kernela, moze li par smernica? Ako neko zna neki forum gde mogu da pronadjem ovaj info, molim neka mi kaze.
Hvala
mada, sada mi pade na pamet, mozda je na toj grani i DVD pa je onda nekako i logicno sto nece da prebaci na udma 5 jel? ;)

Odgovor na temu

mmirilovic
Mladen Mirilović
Čačak

Član broj: 10462
Poruke: 721
*.co.yu
Via: [es] mailing liste

+1 Profil

Re: Suse 9.3 x64 UDMA5 - nece

^{21.06.2005. u 13:12 - pre 242 meseci}

Evo šta kaže "man hdparm" o tome:

Citat:

-i
Display the identification info that was obtained from the drive at boot
time, if available. This is a feature of modern IDE drives, and may not be
supported by older devices. The data returned may or may not be current,
depending on activity since booting the system. However, the current multiple
sector mode count is always shown. For a more detailed interpretation of the
identification info, refer to AT Attachment Interface for Disk Drives (ANSI
ASC X3T9.2 working draft, revision 4a, April 19/93).

-I
Request identification info directly from the drive, which is displayed in a
new expanded format with considerably more detail than with the older -i
flag.

Dakle:
hdaparm -I /dev/hda

Tražio si po svim forumima, a nisi tražio tamo gde treba uvek prvo tražiti!

Pozdrav.

Odgovor na temu

Wakizashi
Novi Beograd

Član broj: 1451
Poruke: 14
*.adsl.sezampro.yu.

Profil

Re: Suse 9.3 x64 UDMA5 - nece

^{21.06.2005. u 15:15 - pre 242 meseci}

ok, da onda apdejtujemo moj prvi post... yast2 kaze da je current mode udma33 a da je required udma100 a posle saveta sa manuelom daje ovo

Code:

/dev/hda:

ATA device, with non-removable media
        Model Number:       TOSHIBA MK6021GAS
        Serial Number:      34470590S
        Firmware Revision:  GA024A
Standards:
        Supported: 5 4 3 2
        Likely used: 6
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  117210240
        device size with M = 1024*1024:       57231 MBytes
        device size with M = 1000*1000:       60011 MBytes (60 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        bytes avail on r/w long: 46     Queue depth: 1
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 16
        Advanced power management level: unknown setting (0x0080)
        DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
udma5
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    NOP cmd
           *    READ BUFFER cmd
           *    WRITE BUFFER cmd
           *    Host Protected Area feature set
           *    Look-ahead
           *    Write cache
           *    Power Management feature set
                Security Mode feature set
           *    SMART feature set
           *    Mandatory FLUSH CACHE command
           *    Device Configuration Overlay feature set
                SET MAX security extension
           *    Advanced Power Management feature set
           *    SMART self-test
           *    SMART error logging
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
        not     supported: enhanced erase
        62min for SECURITY ERASE UNIT.
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by the jumper
Checksum: correct

sto ce reci nema bato brze od udma33
jos neki savet ?

Odgovor na temu