D-Link dsl 300T problem

Pozdrav,da li neko moze da mi pomogne oko settings-a za ovaj modem?

da. user's manual koji si dobio uz njega ti sve objasnjava.

Potpis

OV SM
LA PK

Radio sam sve po njemu ali nikako da se konektuje,u cemu moze biti problem?

U parametrima koji ne odgovaraju mreži na koju pokušavaš da se nakačiš? Da li si kontaktirao podršku svog ISPa radi provere parametara?

Potpis

ex.mangel

Kontaktirao sam ISP-a(Bihnet),rekli su mi da mi nece pomoci jer ne iznajmljujem modem od njih,kakva drskost!Nadao sam se da neko ovde ima ovakav modem ili zna parametre,bas glupa situacija...

1. sledeci put gledaj da das vise detalja o svom problemu u prvom postu, ukoliko zelis koristan odgovor.

2. proveri da li uredno svetli ADSL dioda na samom modemu.

3. otvori web pristup svom modemu, i iskopiraj nam 'system log' da vidimo u cemu je problem.

Potpis

OV SM
LA PK

Ja imam bas takav modem i radi. Pokusacu da ti kazem kako se ja konektujem, mozda ti pomogne, iako si na drugom provajderu.

Prvo, oni nisu obavezni da ti pomazu, ali su duzni da ti dadu parametre za konekciju. Moze i bez toga, metodom probe, ali je zamorno, jer si sada na pocetku pa imas previse stvari da podesavas i isprobavas, lakse je kad bar nesto znas, da manje lutas.

Nadam se da znas da udjes u setup modema i da se tamo kreces. Jedna vazna sitnica - na modemu postoji jedna mala rupa (?) u koju gurnes "ekser" i drzis ga tamo par sekundi i tako vratis modem na fabricke parametre. Medjutim, meni je to bas ruzno i kad sam malo bolje pogledao, isti taj "ekser" postoji i u meniju, moze se modem vratiti na fabricke vrednosti i softverskom komandom iz menija.

Buduci da ja koristim Linux, mozda ti neki moji podaci nece vaziti, ali pretpostavljam da je sve slicno.

Ima jedna kvaka kod korisnickog imena, koje se tamo negde unosi pri podesavanju konekcije. Ja moram da unesem u sledecem obliku [moje korisnicko ime]@verat.net, tako da elektronika u centrali zna na kog provajdera da me usmeri.

Meni je provajder rekao da podesim na modemu "Bridge" nacin i zbog njega mi kartica mora biti BEZ dhcp funkcije, odnosno u nekim distribucijama Linuxa sam jednostavno izabrao opciju "no network" i tako radi.

Potpis

Na svetu postoje samo 2 OS-a: 1. Mint, 2. svi ostali!

Lampice su ok,onako kako pise da treba biti.Probao sam bridge,jedino tako pise da je "connected",ali od interneta nista.Evo log:
Sep 8 12:00:06> Valid Configuration Tree
Sep 8 12:00:11> Firewall NAT service started
Sep 8 12:00:11> Bridge Created: br0
Sep 8 12:00:11> Bridge Interface Added: eth0
Sep 8 12:00:15> DSL Carrier is training
Sep 8 12:00:25> DSL Carrier is up
Sep 8 12:00:25> pppd 2.4.1 started by root, uid 0
Sep 8 12:00:25> Connect: ppp0 {--}
Sep 8 12:01:15> DSL Carrier is training
Sep 8 12:01:25> DSL Carrier is up
Sep 8 12:01:49> Connection terminated.
Sep 8 12:01:49> pppd 2.4.1 started by root, uid 0
Sep 8 12:01:49> default route ioctl(SIOCADDRT): Network is unreachable(128)
Sep 8 12:01:49> WAN IP address 10.64.64.64
Sep 8 12:01:49> WAN gateway 10.112.112.112
Sep 8 12:01:49> PPPoA Connect with IP Address 10.64.64.64
Sep 8 12:01:49> PPPoA Connection Successfully Established
Sep 8 12:01:49> PPPoA Connect with Gateway IP Address: 10.112.112.112
Sep 8 12:02:01> Connect: ppp0 {--}
Sep 8 12:02:28> Connection terminated.
Sep 8 12:02:28> pppd 2.4.1 started by root, uid 0
Sep 8 12:02:28> default route ioctl(SIOCADDRT): Network is unreachable(128)
Sep 8 12:02:28> WAN IP address 10.64.64.64
Sep 8 12:02:28> PPPoA Connect with IP Address 10.64.64.64
Sep 8 12:02:28> WAN gateway 10.112.112.112
Sep 8 12:02:28> PPPoA Connection Successfully Established
Sep 8 12:02:28> PPPoA Connect with Gateway IP Address: 10.112.112.112
Sep 8 12:03:59> pppd 2.4.1 started by root, uid 0
Sep 8 12:04:00> PPPoA Connect with IP Address 10.64.64.64
Sep 8 12:04:00> PPPoA Connection Successfully Established
Sep 8 12:04:00> PPPoA Connect with Gateway IP Address: 10.112.112.112
Sep 8 12:04:00> default route ioctl(SIOCADDRT): Network is unreachable(128)
Sep 8 12:04:00> WAN IP address 10.64.64.64
Sep 8 12:04:00> WAN gateway 10.112.112.112
Sep 8 12:04:09> Bridge Module is stopping and is set at State = 5
Sep 8 12:04:10> Bridge Created: br0
Sep 8 12:04:10> Bridge Interface Added: nas0
Sep 8 12:04:10> Bridge Interface Added: eth0
Sep 8 12:09:24> Bridge Interface Added: nas0

A kod mene pise samo ovo:

Sep 8 12:00:10> Firewall NAT service started
Sep 8 12:00:11> Bridge Created: br0
Sep 8 12:00:11> Bridge Interface Added: nas0
Sep 8 12:00:11> Bridge Interface Added: eth0
Sep 8 12:00:15> DSL Carrier is down
Sep 8 12:00:25> DSL Carrier is up

Imam podeseno sledece:

Status Information
System Uptime 0 hour(s) 59 minute(s)
DSL Status Connected
DSL Speed 64 Kbps Upstream, 256 Kbps Downstream
LAN IP Address 192.168.1.1
Ethernet Connected
DHCP Server Running
Software Version V1.00B01T16.EU.20040212

DHCP Configuration
The device can be setup as a DHCP Server to distribute IP addresses to the LAN network.
Server On

Start IP: 192.168.1.2
End IP: 192.168.1.254
Lease Time: 60 Seconds

Management IP: IP Address:192.168.1.1; NetMask: 255.255.255.0; Hostname: mygateway; Domainname: ar7.

Modem Setup: MMODE

Bridged Connection Setup:
Name: conn1_PPPoE_8_35; Type: Bridge; Bridge Settings:
Encapsulation: LLC ; PVC Settings: VPI: 9; VCI: 35; QoS: UBR.

To bi bilo sve za modem.

Potpis

Na svetu postoje samo 2 OS-a: 1. Mint, 2. svi ostali!

Ovo pise u konzoli (terminalu), ali moram da naglasim da je ovo stanje sa aktiviranom mreznom karticom. Da je nisam aktivirao ne bih mogao da pristupim modemu. U redovnom radu, kartica nije aktivirana i vidi se nekako drugacije, ima samo hardversku adresu, ali to sada ne mogu da snimim, moram da uradim reboot racunara da bi se kartica vratila u to "pasivno" stanje. Naravno, o mrezama nemam pojma, ovo sam nekako isceprkao probajuci i posto radi, to je to.

root@24[tdjokic]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:50:8D:66:BA:EE
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::250:8dff:fe66:baee/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6102 errors:0 dropped:0 overruns:0 frame:0
TX packets:6195 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4315676 (4.1 MiB) TX bytes:723226 (706.2 KiB)
Interrupt:15 Base address:0x5000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:644 (644.0 b) TX bytes:644 (644.0 b)

ppp0 Link encap:Point-to-Point Protocol
inet addr:62.108.117.164 P-t-P:217.26.64.4 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1
RX packets:126 errors:0 dropped:0 overruns:0 frame:0
TX packets:140 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:86547 (84.5 KiB) TX bytes:27706 (27.0 KiB)

Potpis

Na svetu postoje samo 2 OS-a: 1. Mint, 2. svi ostali!

Ima nekih slicnosti,ali nije isto naravno.Ne razumijem stvarno,ima setup u 5 koraka,trebalo bi biti lagano,mora da ja grijesim u necemu..

Prebaci modem iz PPPoA ili PPPoE moda u Bridge !

Potpis

Goglasi! - Šta god da kupuješ, naći ćeš na Goglasima! Pretraga malih oglasa i eProdavnica, preko 10 milionda proizvoda.

Cityexpert.rs - Prva srpska onlajn agencija za nekretnine

ॐ

Ok,prebacio sam,dobijem connected,sta se desava sa username i pass-om,jer kad ga prebacim u bridge to nemam nigdje da upisem

moras da napravis na compu konekciju.

start>settings>network conn>new conn wizard>to the internet>manual>broadband w/ username and pass>kucaj tu user i pass

i svaki put kad hoces da se konektujes startujes tu konekciju, kao sto si ranije radio sa dial-up.

Potpis

OV SM
LA PK

Konekciju sam napravio,pokusavam ali dobijem :error 678 The remote computer did not respond.
Ovako:

Imam 2 mrezne karte,oba racunara mi u mrezi rade ok(crossover),konekciju sam prije ove imao sa lucentovim modemom,radilo je na oba bez problema.Uradio sam ponovo network setup wizard,tu sam rekao da ovaj komp ide dir.na internet,da se ostali kace preko njega.Znaci,ova 2 kompa se sasvim ok vide.

Evo postavki u modemu:

Status Information
System Uptime 0 hour(s) 3 minute(s)
DSL Status Connected
DSL Speed 160 Kbps Upstream,
1024 Kbps Downstream
LAN IP Address 192.168.1.1
Ethernet Connected
DHCP Server Running
Software Version V1.00B02T02.EU.20040618

Enable DHCP Server
Start IP: 192.168.1.2
End IP: 192.168.1.254
Primary DNS: 192.168.1.1
Lease Time: 60 Seconds


Management IP


IP Address 192.168.1.1
NetMask 255.255.255.0

Select the Modulation type
MMODE


Connection Status

LAN
MAC Address 00:11:95:CA:14:24
IP Address 192.168.1.1
Subnet Mask 255.255.255.0
DHCP Server Running

WAN



Description Type IP State Action
Connection 1 bridge 0.0.0.0 Connected


LOG:

Sep 8 12:00:11> Firewall NAT service started
Sep 8 12:00:11> Bridge Created: br0
Sep 8 12:00:12> Bridge Interface Added: eth0
Sep 8 12:00:12> Bridge Interface Added: nas0
Sep 8 12:00:15> DSL Carrier is training
Sep 8 12:00:25> DSL Carrier is up
Sep 8 12:07:45> DSL Carrier is training
Sep 8 12:07:55> DSL Carrier is up
Sep 8 12:08:34> Bridge Interface Added: nas0

Sta sam pogresno uradio,sta ne valja?

Sredio!!!
Jedina razlika je u VPI -1 i VCI -35,zavisi znaci od provajdera,,,
Anyway,hvala puno svima!