[es] - Suse 9.0 - Samsung 795mb sync problem?

Opusteno
Predrag Manojlovic
Cacak

Član broj: 3732
Poruke: 35
*.vdial.verat.net.

Profil

Suse 9.0 - Samsung 795mb sync problem?

^{13.11.2004. u 08:59 - pre 236 meseci}

SuSE 9.0 - Samsung 795MB SYNC PROBLEM?

Konfiguracija je sledeca
AMD DURON 840Mhz, 256 SDRAM, GeForce 256, HDD 20GB, Monitor Samsung 795MB
Pored vec postojeceg sistema WinXP (na hda1, NTFS) i druge particije hda5 (NTFS), instalirao sam SuSE9.0.
Instalacija je isla ok do kraja ali problem se javio kada sam posle toga hteo da prvi put koristim Suse...
u trenutku kada bi trebalo da se pojavi desktop, umesto istog ostaje crni ekran sa uokvirenim kvadraticem
u kome pise "sync Hz?". Znam da je problem u tome sto monitor nije prepoznao kao "SyncMaster 795MB" vec kao
"Samsung 4*". Pomocu Knoppix v3.3 sam pokusao da dodjem do /hda7/etc/x11/xf86config i da u istom fajlu promenim
same -HSync i -VSync kao i default rezoluciju ... sve to sam i uspeo. Problem je u tome sto ne znam kako da tu promenu
sacuvam u xf86config fajlu!? pokusao sam sa mount /dev/hda7 i umount /dev/hda7 ali mi ne uspeva tj. dobijam poruku pri
pokusaju snimanja da je fajl write protected.
Pretpostavljam da su ovo neki pocetnicki problemi ali oni su meni za sada najveci...
Ponavljam da ovom fajlu mogu da pristupim samo iz Knoppixa... mada verovatno postoje i drugi nacini
hvala unapred

Black Rock

Odgovor na temu

Mister-Stoka
Radomir Radojevic
NS

Član broj: 35357
Poruke: 15
*.nat-pool.nsad.sbb.co.yu.

Profil

Re: Suse 9.0 - Samsung 795mb sync problem?

^{13.11.2004. u 10:17 - pre 236 meseci}

Au bato ala si ga ti zamrsio...:) znaci pokushavash da editujesh xf86config file preko knoppixa kod vec zdravog i pravog SuSE-ta...bre ovako cemo mi to...
dakle lepo ti podignesh sistem...ili ...pa kad se spuca monitor....ti cepaj ctrl+alt+F1
pa pedjina prvu tty konzolu ...loguj se kao root pa kucaj mcedit /etc/X11/xf86config ili je to xf86config-4 file nsiam siguran kako to beshe kod suse-ta.....pre ce biti da je to ovaj drugi....pa onda lepo uzmesh i editujesh file
kod section "Monitor" kod mene to izgleda ovako:

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

Identifier "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

31.5 - 50.0

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 40-90

EndSection

znaci zajebi tip monitora...odrqadi samo HorizSync i VertRefresh
uzmesh lepo neki prirucnik za tvoj monitor i to odradish

onda :

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "VESA Framebuffer"
Monitor "My Monitor"

# If your card can handle it, a higher default color depth (like 24 or 32)
# is highly recommended.

# DefaultDepth 8
# DefaultDepth 16
DefaultDepth 24
# DefaultDepth 32

# "1024x768" is also a conservative usable default resolution. If you
# have a better monitor, feel free to try resolutions such as
# "1152x864", "1280x1024", "1600x1200", and "1800x1400" (or whatever your
# card/monitor can produce)

Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubsection
Subsection "Display"
Depth 24
Modes "800x600" "640x480"
EndSubsection
Subsection "Display"
Depth 32
Modes "1024x768" "800x600" "640x480"
EndSubsection

EndSection

dakle obrati paznju na DefaultDepth kod mene je DefaultDepth 24 verovatno i kod tebe
e onda Subsection "Display" deph 24 kod mene je modes "800x600" "640x480"
jer imam neki skrnavu petnaestoincnu noname-ichinu....znaci to regulishi....rezoluciju koju podrzava tvoj monitor....kod mene se recimo spucava...na 1024x768 pa sam to uklonio...
Samo na kraju ako vec ti se toliko ubije monitor...da na kraju iz ocaja morash u knoppix..oda lepo ....iz grafaje ..desni klick na /dev/hda7 na desktopu jer cini mi se da knoppix pravi shotcut ...i da imash opciju da tu particiju ucinish read & write ....i odna edituj ***i ga

Odgovor na temu