[es] - nazalost... jos jedan lucent :)

Milan Andjelkovic
Product Manager
Tegus Medical
Beograd

Član broj: 4476
Poruke: 3281
*.31.EUnet.yu

Sajt: www.linkedin.com/in/milan..

+8 Profil

nazalost... jos jedan lucent :)

^{22.02.2003. u 23:24 - pre 270 meseci}

imam lucentov winmodem (da, hvala, znam da to nisu modemi... :).
skinuo sam rpm verziju drajvera sa neta, i testirao modem.
u wvdial-u on odradi inicijalizaciju, zatim usledi vise OK-ova (ATZ, ATX3) a zatim ide ATDT3105050 i - nista. ama bas nista se ne desava.
probao sam i iz minicom-a i slicna se stvar desava, samo sto on posle 30-ak sekundi izbaci no carrier (ako se dobro secam, jer ovo pisem iz win-a).
sa kppp takodje - test modem je radio i detektovao lucenta, ali kada krenem da okrecem opet vise OK-ova i nista.

da li je mozda u pitanju neodgovarajuci drajver?

inace, koristeci lspci -v sam dobio:

00:11.0 Communication controller: Lucent Microelectronics: Unknown device 048c (rev 02)
Subsystem: Lucent Microelectronics: Unknown device 044c
Flags: bus master, medium devsel, latency 32, IRQ 11
Memory at de000000 (32-bit, non-prefetchable) [size=256]
I/O ports at dc00 [size=8]
I/O ports at e000 [size=256]
Capabilities: [f8] Power Management version 2

a koristeci lspci -nv :

00:11.0 Class 0780: 11c1:048c (rev 02)
Subsystem: 11c1:044c
Flags: bus master, medium devsel, latency 32, IRQ 11
Memory at de000000 (32-bit, non-prefetchable) [size=256]
I/O ports at dc00 [size=8]
I/O ports at e000 [size=256]
Capabilities: [f8] Power Management version 2

da li iz ovoga neko moze da mi kaze da li mi je modem uopste podrzan?

distribucija je RH 8.0

saveti i objasnjenja su dobrodosli :)

ex.mangel

Odgovor na temu

Miško Stefanović
Beograd

Član broj: 5698
Poruke: 218
*.beograd-3.tehnicom.net

Profil

Re: nazalost... jos jedan lucent :)

^{26.02.2003. u 02:36 - pre 270 meseci}

Isti štos samo upakovano u SuSE 8.1.

Ništa nisam uspeo čarobnjacima...Pokušaj grubom silom otvori config za wvdial (ne znam sintaksu za RH) u bilo kom editoru i ukucaj sve što je prazno, br. telefona, usename, password i posle ATDT3105050 moraš da dobiješ waiting for carrier ako ti je centrala tonska. Ako je pulsna ATDP....

Nije teško pokušati. Možda uspe, bar meni je uspelo bez obzira što sam trenutno pod Win. Ovoliko o wvdial. Uzgred, da li je centrala stvarno tonska?

Javi, Pozdrav.

P.S. Modem je ipak modem, kad sam ja imao sličnih problema dobijao sam bezsmislene i nepristojne odgovore, to me primoralo da sam rešim problem, jasno je da hoću iskreno da ti pomognem jer imam i MANDRAKE koji je isto baziran na rpm. Uzgred, koji je kernel i koja verzija rpm. Možda stvarno nije dobar driver? mada mi to deluje čudno ako ga kppp vidi.

Odgovor na temu

Milan Andjelkovic
Product Manager
Tegus Medical
Beograd

Član broj: 4476
Poruke: 3281
*.179.EUnet.yu

Sajt: www.linkedin.com/in/milan..

+8 Profil

Re: nazalost... jos jedan lucent :)

^{27.02.2003. u 15:47 - pre 270 meseci}

heh... da:

Code:
[root@localhost root]# wvdial
--> WvDial: Internet dialer version 1.53
--> Initializing modem.
--> Sending: ATX3
ATX3
OK
--> Sending: AT S11=50
AT S11=50
OK
--> Modem initialized.
--> Sending: ATDT3105050
--> Waiting for carrier.
ATDT3105050
NO CARRIER
--> No Carrier! Trying again.
--> Sending: ATDT3105050
--> Waiting for carrier.
ATDT3105050

sve on to odradi, međutim, ništa se ne desava. nakon ATDT3105050 se ništa ne dešava oko 1min. i onda izbaci NO CARRIER. Ono što mi je bilo malo čudno jeste da mi sistem veoma sporo radi nakon što pokrenem wvdial (čak je i kursor miša usporen) i tako sve dok ga ne isključim.
centrala jeste tonska.

wvdial.conf izgleda ovako:

Code:
[Dialer Defaults]
Modem = /dev/modem
Baud = 115200
Init = ATX3
Init2 = AT S11=50
Phone = 3105050
Username = milan.a
Password = *****

[Dialer shh]
Init3 = ATM0

[Dialer Tone]
Dial Command = ATDT

što se tiče kernela i rpm-a:

Code:
[root@localhost root]# uname -r
2.4.18-14
[root@localhost root]# rpm -q -a ltmodem*
ltmodem-kv_2.4.18_14-8.26a9-1

a sam rpm file je:

ltmodem-kv_2.4.18_14-8.26a9-1.i686.rpm

još su mi dve stvari nejasne iz same instalacije:

Code:
[root@localhost Modem]# rpm -ivh ltmodem-kv_2.4.18_14-8.26a9-1.i686.rpm
Preparing... ########################################### [100%]
warning: user rda does not exist - using root
warning: group midas does not exist - using root

...ove poslednje dve linije ponavlja jedno 30-ak puta. šta one predstavljaju?

ostatak instalacije izgleda ovako:

Code:
   1:ltmodem-kv_2.4.18_14   ########################################### [100%]
Diagnostic information is being written to /usr/share/doc/ltmodem-kv_2.4.18_14-8.26a9/LTinstall.txt

scanmodem finished, proceeding with autoload section

   Made modem device node    /dev/ttyLT0
     group ownership set to uucp
   with symbolic link    /dev/modem --> /dev/ttyLT0
Writing modules autoloading lines to /etc/modules.conf:
Using /sbin/depmod
Updating with:  /sbin/depmod -a
Capturing output to /tmp/ltmodem/tmpfile and parsing.

...sad nastupa deo koji mi nije jasan:

Code:

Your system is lacking Default lines in /etc/modules.conf
which are usually needed to support the modem communications protocol PPP.
Some modem installations replace these Defaults
    with lines specific to particular modem hardware.
There may be problems using the Lucent/Agere modem without these Default lines.
The suspect lines are:
------------------------------
  cat /tmp/ltmodem/tmpfile
------------------------------
and are being inserted in /usr/share/doc/ltmodem-kv_2.4.18_14-8.26a9/LTinstall.txt for your judgement.
Should you insert them in /etc/modules.conf, inform the System with
   /sbin/depmod -a

...i ostatak...

Code:
The modem drivers dependencies are properly resolved.

A folder has been installed in your Systems documentation,
  /usr/share/doc/ltmodem-kv_2.4.18_14-8.26a9
containing much useful guidance and uilities. Updates can be
downloaded from http://www.heby.de/ltmodem/ as DOCs.tgz

To get online, the Port to be specified in your dialout scripts is:
/dev/ttyLT0 or its symbolic, /dev/modem
A summary of installation actions with Advice is contained in: /usr/share/doc/ltmodem-kv_2.4.18_14-8.26a9/LTinstall.txt

  Browse DOCs/Ltmodem.html for issues that may be relevant to your system and useful URLs
  Also see DOCs/LastAdvice
  Some dialer utilities including KPPP require that Each User set up a configuration,
  as there could be diverse configurations on multi-User systems.

  Read DOCs/wvdial.txt for aid in configuring the smart dialup utility, WVDIAL

        Otherwise, get Online and Enjoy
        Relate problems to discuss@linmodems.org
        Gratitude too,  to discuss@linmodems.org

If not familar with the ltmodem drivers, run the interactive CHECKOUT utility by executing:
        /usr/share/doc/ltmodem-kv_2.4.18_14-8.26a9/utils/checkout

izvinjavam se na poduzem postu.

ex.mangel

Odgovor na temu

Tigerheart
Mladen Komac
VMware SME / IT Architect
NIL ltd.
Celje

Član broj: 306
Poruke: 461
*.etf.bg.ac.yu

Jabber: tigerheart@elitesecurity.org
Sajt: www.linkedin.com/in/komac

Profil

Re: nazalost... jos jedan lucent :)

^{27.02.2003. u 17:11 - pre 270 meseci}

Pokusaj jos jednu stvar ... da odradis sve iz source-a lt drajvera .. moze da prodje... ( bar je meni prolaznost bila nekih 90% na masinama koje sam instalirao)
http://phep2.technion.ac.il/goldberg/post-install.html

Takodje pogledaj i koju si zemlju stavio .. u vecini slucajeva US odradjuje posao .... pogledaj takodge Germany ili npr Italy .....
Pogledaj AT komande modema ..... za vise informacija pogledaj sledece :
http://www.physcip.uni-stuttgart.de/heby/ltmodem/doc/modem600.pdf
Javi sta si uradio ....

--
Mladen Komac
VMware SME / IT Architect
Web site: http://www.linkedin.com/in/komac
Blog: http://guru4hp.blogspot.com

Odgovor na temu