philips dvp630 dvd-divx

bakara: pa izgleda da jeste novija 0112 je izasla 14.01.2005, a ova sto sada moze da se skine 08.06.2005...Mislim, obe su bajate!

Ali ne vidim razloga da menjam ovaj fw 112, za nijednan drugi, ne razumem zasto bi menjali tu verziju?
Sta to moze bolje od toga?

bakara: Kako to mislis ne cita dobro, ili cita ili ne cita...ako si mislio na odnos slike, ja tu ne vidim nista lose, e sad sto nema malo manji zoom jbga, ne mora ni da ga ima, ko to jos koristi osim na compu.

A sto se tice kodeka, ja gledam bar 2 filma dnevno na njemu i bas, bas retko se desi da nesto ne moze da se otvori, mozda jedan od 50. Ako si misli na brljavu sliku kod xvida za to smo vec pominjali resenje...

Ja bolji player jos nisam video a proslo mi je kroz ruke bar 10 modela (cak i noviji philipsi), a rado bih zamenio ovaj matori philips za neki noviji, pod uslovom da je bolji.

Memomax: jasno sam napisao "uopste ne cita dobro". dakle, jos jasnije, Philips 630/632 ne ume, ne zna, tehnicki nije sposoban da pravilno ocita aspect ratio, odnos slike kako kazes, kod Divx filmova. nisam naglasio, imam 16:9 televizor, i Philips svaku 16:9 Divx sliku uporno vidi kao 4:3, tako da umesto pravilnog odnosa slike ja na mom 16:9 TV-u gledam suzenu sliku, sto je nedopustivo.

bakara: Malo cudno, na to se jos niko nije zalio, a nisi ti prvi sa wide TVom, jeis podesio u opcijama video setup/tv display/16:9
I ako nesto treba na tVu...

bakara: Ako me dobro secanje sluzi, u ovom topicu je bilo komentara i pitanja za
wide TV, i nije bilo problema...
E sad ne znam....

1. Software Upgrade Procedure
Note: Do not press any button or unplug the Mains/AC during upgrade.
1. Connect the Mains/AC cord to the wall socket. Press “STANDBY -ON” button on the front-panel or “
POWER” button on the remote control to activate the player.
2. Press “ OPEN/CLOSE” to open the disc tray.
3. Insert the upgrade CD-ROM disc, label side up.
4. Press “ OPEN/CLOSE” to close the disc tray.
· TV screen will show : “DISC LOADING” “FLASH” “DVPXX.ROM” “READING” “FLASH” “ERASE”
“WRITE” “DONE”.
· Player display will show : “LOADING” “ERASE” “WRITE” “DONE”.
· This stage of the proc edure takes about 2 minutes.
· If the software was successfully downloaded, the DVD-player will turn Off automatically.
5. Unplug the Mains/AC cord from the wall socket.
6. After 15 seconds, reconnect the Mains/AC cord to the wall socket and turn On the Mains/AC supply.
7. Press “ OPEN/CLOSE” button on the Front Panel to activate the player.
· The player will initialise for the first 3-4 seconds. Do not press any other buttons.
· After 3-4 seconds delay , the disc tray will open.
· Remove the disc immediately.
Note : If for some reason the disc tray did not open , allow the player to repeat the upgrade until it
turns Off automatically again. Then follow the instructions above again to remove the disc.
Never interrupt the upgrading midway as this will damage the player. Always wait till the player has
turn Off automatically.
8. The DVD-player will function as per normal.
Note: If the display shows “FAIL”, please refer to the Philips Care Center.