Je li neko nakada probao da instalira ovako nesto, ceo dan trazim na internetu i nikako da podesim. Finta je sto nemam windows a nikako da ga podesim na Gentoo-u a "volja mi" da vidim kako sve to radi. Naravno sve zasta mi treba je crtanje, dakle vucenje po podlozi, levi i desni taster misa.
Tablet GeniusWizardPen 4X3
Zaključano
Zakačeno
Do sada sam provalio da postoje drajveri za WizardPen 5X5 bazirani na acecad drajveru ali
(EE) xf86OpenSerial: Cannot open device /dev/input/event0
No such device.
(EE) AceCad driver unable to open device
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
(EE) xf86OpenSerial: Cannot open device /dev/input/event0
No such device.
(EE) AceCad driver unable to open device
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
# cd /usr/src/linux
# make menuconfig
Podješ na "Device Drivers-->Input device support" postavis polje za selekciju iznad "< > Event interface". Ako pritisnes Help u tom ekranu, naci ces na ovakvu recenicu:
Pritisni dugme Y ili M, izadji, sacuvaj konfiguraciju i iskompajliraj novi kernel kako je objasnjeno u prirucniku, poglavlje manualna konfiguracija kernela. Restartuj, probaj, mozda proradi.
# make menuconfig
Podješ na "Device Drivers-->Input device support" postavis polje za selekciju iznad "< > Event interface". Ako pritisnes Help u tom ekranu, naci ces na ovakvu recenicu:
Code:
Say Y here if you want your input device events be accessible
under char device 13:64+ - /dev/input/eventX in a generic way.
To compile this driver as a module, choose M here: the
module will be called evdev.
Say Y here if you want your input device events be accessible
under char device 13:64+ - /dev/input/eventX in a generic way.
To compile this driver as a module, choose M here: the
module will be called evdev.
Pritisni dugme Y ili M, izadji, sacuvaj konfiguraciju i iskompajliraj novi kernel kako je objasnjeno u prirucniku, poglavlje manualna konfiguracija kernela. Restartuj, probaj, mozda proradi.
A ako do sada koristio genkernel, prije nego sto pocnes procitaj Gentoo Linux Kernel Upgrade Guide i obavezno sacuvaj stari kernel i par linija u konfiguracionom fajlu u tvog boot loadera koje su posvecene njegovom dizanju, da mozes da se vratis na staru konfiguraciju, ako nesto zabrljavis pri kompajliranju.
Mislim da je to ukljuceno po defaultu, nego sad cu da proverim i rekoplajliram ako treba. A predpostavljam da mogu i
#genkernel --menuconfig
all, zar ne?
#genkernel --menuconfig
all, zar ne?
E to je to, hvala ti, sad vidim neki rezultat, doduse nedovoljan ali...
I kad se startuje X mis radi normalno a na tabletu cim kliknem neko dugme ili prevucem, kursor jednostavno ode u gornji levi cosak i ne mrda dok ne pokrenem misa, gr...
evo kako mi je podesen X
u Server Layout
u input device
koristim drajver sa
http://www.stud.fit.vutbr.cz/~...ndex.php?page=Genius_WizardPen
Citat:
(**) Option "Device" "/dev/input/event2"
(**) Mouse2 Tablet model is unspecified
(**) Kernel Input driver version is 1.0.0
(**) Kernel Input device name: "UC-LOGIC Tablet WP4030U"
(**) Acecad Tablet MaxX:31000 MaxY:31000 MaxZ:1023
(**) Acecad Tablet is in absolute mode
(**) Mouse2 Tablet is using standard button map
(**) Option "AlwaysCore"
(**) Mouse2: always reports core events
(II) XINPUT: Adding extended input device "Mouse2" (type: AceCad Tablet)
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
(II) XINPUT: Adding extended input device "NVIDIA Event Handler" (type: Other)
(**) Acecad Tablet Device Init
(**) Acecad Tablet Control Proc
(**) Acecad Tablet Increment: 24
(II) Mouse1: ps2EnableDataReporting: succeeded
(**) Acecad Tablet Device On
(**) Mouse2 Tablet model is unspecified
(**) Kernel Input driver version is 1.0.0
(**) Kernel Input device name: "UC-LOGIC Tablet WP4030U"
(**) Acecad Tablet MaxX:31000 MaxY:31000 MaxZ:1023
(**) Acecad Tablet is in absolute mode
(**) Mouse2 Tablet is using standard button map
(**) Option "AlwaysCore"
(**) Mouse2: always reports core events
(II) XINPUT: Adding extended input device "Mouse2" (type: AceCad Tablet)
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
(II) XINPUT: Adding extended input device "NVIDIA Event Handler" (type: Other)
(**) Acecad Tablet Device Init
(**) Acecad Tablet Control Proc
(**) Acecad Tablet Increment: 24
(II) Mouse1: ps2EnableDataReporting: succeeded
(**) Acecad Tablet Device On
I kad se startuje X mis radi normalno a na tabletu cim kliknem neko dugme ili prevucem, kursor jednostavno ode u gornji levi cosak i ne mrda dok ne pokrenem misa, gr...
evo kako mi je podesen X
u Server Layout
Citat:
InputDevice "Mouse2" "AlwaysCore"
u input device
Citat:
Section "InputDevice"
Identifier "Mouse2"
Driver "acecad"
Option "Device" "/dev/input/event2"
Option "Mode" "Absolute"
EndSection
Identifier "Mouse2"
Driver "acecad"
Option "Device" "/dev/input/event2"
Option "Mode" "Absolute"
EndSection
koristim drajver sa
http://www.stud.fit.vutbr.cz/~...ndex.php?page=Genius_WizardPen
Iskreno na SuSE 9.1 WizzardPen je proradio iz prve (samo je bi isključen prilikom instalacije).
Za prethodne distribucije koristio sam uputstva sa [url]http://www.genius-europe.com/service/faq/tuxtablet.htm[/url] ali bez nekog većeg uspeha.
Evo kako kod mene sada izgledaju bitni delovi XF86Config fajl (znam da ti osim gpm-a treba i usb kernel modul instaliran ali da li je uhci ili ohci ne sećam se).
Section "Files"
InputDevices "/dev/gpmdata"
InputDevices "/dev/mouse"
InputDevices "/dev/usbmouse"
InputDevices "/dev/input/mice"
....
End Section
Section "ServerFlags"
Option "AllowMouseOpenFail"
Option "RandR" "on"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "speedo"
Load "freetype"
Load "extmod"
Load "glx"
Load "v4l"
Load "dri"
EndSection
Section "InputDevice"
Driver "summa"
Identifier "Mouse[3]"
Option "AlwaysCore" "on"
Option "BaudRate" "19200"
Option "Cursor" "Stylus"
Option "Device" "/dev/input/event0"
Option "InputFashion" "Tablet"
Option "Mode" "Absolute"
Option "Name" "SUMMASKETCH"
Option "Vendor" "SUMMAGRAPHICS"
EndSection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
InputDevice "Mouse[3]" "SendCoreEvents"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection
Za prethodne distribucije koristio sam uputstva sa [url]http://www.genius-europe.com/service/faq/tuxtablet.htm[/url] ali bez nekog većeg uspeha.
Evo kako kod mene sada izgledaju bitni delovi XF86Config fajl (znam da ti osim gpm-a treba i usb kernel modul instaliran ali da li je uhci ili ohci ne sećam se).
Section "Files"
InputDevices "/dev/gpmdata"
InputDevices "/dev/mouse"
InputDevices "/dev/usbmouse"
InputDevices "/dev/input/mice"
....
End Section
Section "ServerFlags"
Option "AllowMouseOpenFail"
Option "RandR" "on"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "speedo"
Load "freetype"
Load "extmod"
Load "glx"
Load "v4l"
Load "dri"
EndSection
Section "InputDevice"
Driver "summa"
Identifier "Mouse[3]"
Option "AlwaysCore" "on"
Option "BaudRate" "19200"
Option "Cursor" "Stylus"
Option "Device" "/dev/input/event0"
Option "InputFashion" "Tablet"
Option "Mode" "Absolute"
Option "Name" "SUMMASKETCH"
Option "Vendor" "SUMMAGRAPHICS"
EndSection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
InputDevice "Mouse[3]" "SendCoreEvents"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection
Potpis
Bratislav Velickovic
hhtp://blog.velickovic.net
hhtp://blog.velickovic.net
Probao sam ovo gore i sa summa i acecad modulima, ocitam gpm sa acecad i namestim acecad u xorg.conf, restartujem X i nista, ubijem gpm, ucitam summa... i nista
Mozda nijesi ubo pravi uredjaj za tablet (montirace tamo i mouse). Uradi:
#cat /dev/input/event2
I probaj da nesto radis sa tabletom. Ako se na ekranu pojavi neko djubre, onda je OK, to je tvoj uredjaj. Ako ne, trazi drugi event. Eh da, ne zaboravi da onaj cat ubijes sa <Ctrl-C>.
#cat /dev/input/event2
I probaj da nesto radis sa tabletom. Ako se na ekranu pojavi neko djubre, onda je OK, to je tvoj uredjaj. Ako ne, trazi drugi event. Eh da, ne zaboravi da onaj cat ubijes sa <Ctrl-C>.
lsmod kod mene daje sledeće module:
usbcore
cdc_acm
usbserial
hid
ehci_hcd
ihci_hcd
usbcore
cdc_acm
usbserial
hid
ehci_hcd
ihci_hcd
Potpis
Bratislav Velickovic
hhtp://blog.velickovic.net
hhtp://blog.velickovic.net
cat /dev/input/event0 daje neke znake zivota, a cat /dev/input/event2 daje znake zivota tek kad olovkom dodirnem podlogu
Ovo su moji moduli
ohci_hcd 18180 0
ehci_hcd 25348 0
uhci_hcd 28304 0
usbhid 29760 0
acecad 6656 0
usbcore 95840 9 slusb,ohci_hcd,ehci_hcd,usblp,uhci_hcd,usbhid,acecad
Nemam modul usbserial izgleda da nisam ukljucio podrsku za njega
Ovo su moji moduli
ohci_hcd 18180 0
ehci_hcd 25348 0
uhci_hcd 28304 0
usbhid 29760 0
acecad 6656 0
usbcore 95840 9 slusb,ohci_hcd,ehci_hcd,usblp,uhci_hcd,usbhid,acecad
Nemam modul usbserial izgleda da nisam ukljucio podrsku za njega
Evo ga drajver ako nekom zatreba
Radi 100% a za wizardpen 5x5 treba koristiti onaj prvi, hvala svima na pomoći
Radi 100% a za wizardpen 5x5 treba koristiti onaj prvi, hvala svima na pomoći