Navigacija
Lista poslednjih: 16, 32, 64, 128 poruka.

CISCO 1600 router+Leased Line problemi

[es] :: Enterprise Networking :: CISCO 1600 router+Leased Line problemi

Strane: 1 2 3 4

[ Pregleda: 15700 | Odgovora: 61 ] > FB > Twit

Postavi temu Odgovori

Autor

Pretraga teme: Traži
Markiranje Štampanje RSS

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon CISCO 1600 router+Leased Line problemi25.06.2004. u 17:02 - pre 240 meseci
imam problem da podignem moj cisco router na iznajmljenoj liniji. prikljucio sam modem preko kabla (w35) a u router na drugom kraju kabla ukljucio u serijski port. Konfigurisao LAN ethernet na 10.40.0.1 IP adresi...serial na svojoj jedinoj public IP adresi i nece da proradi..dobijam ppppppppppporuku:

show interface serial 0
Serial0 is up, line protocol is down

Pomogajte


[Ovu poruku je menjao _tux_rulez dana 25.06.2004. u 20:31 GMT]
Tux The Killer
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi25.06.2004. u 17:27 - pre 240 meseci
ROUTER#show interface serial 0
Serial0 is up, line protocol is down
Hardware is QUICC Serial
Internet address is 80.65.91.86/30
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation PPP, loopback not set, keepalive set (10 sec)
LCP Listen
Closed: ipcp, cdp
Last input 00:00:00, output 04:31:11, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/64/0 (size/threshold/drops)
Conversations 0/7 (active/max active)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
5178 packets input, 124272 bytes, 0 no buffer
Received 4003 broadcasts, 0 runts, 0 giants
1626 input errors, 0 CRC, 1599 frame, 0 overrun, 0 ignored, 27 abort
5218 packets output, 168063 bytes, 0 underruns
0 output errors, 0 collisions, 3314 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=down CTS=down


[Ovu poruku je menjao _tux_rulez dana 25.06.2004. u 20:33 GMT]
Tux The Killer
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi25.06.2004. u 18:30 - pre 240 meseci
RTS - Request To Send
CTS - Clear To Send

Bojim se da nije kabl ostecen...

Tux The Killer
 
Odgovor na temu

nkrgovic
Nikola Krgović
Beograd

Član broj: 3534
Poruke: 2807

ICQ: 49345867
Sajt: https://www.twinstarsyste..


+655 Profil

icon Re: CISCO 1600 router+Leased Line problemi26.06.2004. u 00:27 - pre 240 meseci
Citat:
_tux_rulez: ROUTER#show interface serial 0
Serial0 is up, line protocol is down
Hardware is QUICC Serial
Internet address is 80.65.91.86/30]


Ovo je, koliko se ja razumem : "Interfej sam podigao, ali nista ne vidim iza". Moguce da je kabl, a moguce da parametri nisu dobri. Kako je V.35 kabl prilicno ogomantna i rogobatan (da li si dobro spojio? Treba da se DODIRUJU povrsine konektora - tj. da to sve lepo prisrafis) ja bi svakako prvo proverio parametre (enkapsulacija i tako to), pa onda tek trazio nov kabl.
Please do not feed the Trolls!

Blasphemy? How can I blaspheme? I'm a god!'
 
Odgovor na temu

Dusan Marjanovic
Consultant, SAS
Beograd

Član broj: 59
Poruke: 1290
*.info-net.co.yu

Jabber: dusanm@gmail.com
ICQ: 84621598
Sajt: marjanovic.net


+6 Profil

icon Re: CISCO 1600 router+Leased Line problemi26.06.2004. u 09:07 - pre 240 meseci
imao sam problem koji se slicno manifestovao, a u pitanju je bilo da je kabl na krajevima imao potrebne konektore ali zice drugacije rasporedjene, tako da je sve pasovalo kako valja, ali link nikako...
VMware VCP/Microsoft MCSE 2003/HP ASE
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi26.06.2004. u 16:20 - pre 240 meseci
Prije svega hvala na odgovorima. Enkapsulacija je ppp, kako mi je ISP rekao, kabl cu pokusati da odnesem kod nekoga ko ima istu vrstu konekcije, pa cu kod njega isprobati kabl....ako ne bude radio na njegovom routeru i modemu onda...je do kabla...javim rezultate
Tux The Killer
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 09:42 - pre 240 meseci
Upravo sam iz mog ISP-a dosao sa originalnim cisco system kablom, koji je dva dana prije skinut sa routera koji je radio. Umjesto mog, stavim novi kabl, i opet ista stvar...
Sta sada? uradim show interface Serial 0 i opet stoji isti message....line protocol is down?! Na koji setting da gledam?
Tux The Killer
 
Odgovor na temu

markom
Marko Milivojević
Network Engineer
Google
Mountain View

Član broj: 18427
Poruke: 4227
*.lina.net

Sajt: https://markom.rs


+16 Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 10:24 - pre 240 meseci
Jesi probao da resetuješ modem?

Pošalji ovde output od "show tech-support" za početak.


Marko.
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 11:51 - pre 240 meseci
Modem je takav da se ne moze resetovati. Tako su mi i rekli u ISP-u, odnosno tel kablom direkt na liniju sa koje izgleda uzima i napajanje itd....a taj kabl je unutar njega zabicom spojen tako da se ne moze izvuci.....

tech-support dolazi za minutu...
Tux The Killer
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 12:11 - pre 240 meseci
Code:

MEMO#show tech-support

------------------ show version ------------------

Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.1(12)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1997 by cisco Systems, Inc.
Compiled Mon 09-Jun-97 14:20 by krunyan
Image text-base: 0x0200544C, data-base: 0x022C4494

ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
ROM: 1600 Software (C1600-RBOOT-R), Version 12.0(3)T,  RELEASE SOFTWARE (fc1)

MEMO uptime is 34 minutes
System restarted by power-on
System image file is "c1600-y-l.111-12.AA", booted via flash

cisco 1601 (68360) processor (revision C) with 7680K/512K bytes of memory.
Processor board ID 14711395
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface.
1 Serial(sync/async) network interface.
System/IO memory with parity disabled
8192K bytes of DRAM onboard
System running from RAM
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read/Write)

Configuration register is 0x2102


------------------ show running-config ------------------


Building configuration...

Current configuration:
!
version 11.1
service config
service udp-small-servers
service tcp-small-servers
!
hostname MEMO
!
enable secret 5 <removed>
enable password <removed>
!
ip subnet-zero
ip address-pool local
!
interface Ethernet0
 ip address 10.40.0.1 255.255.0.0
 no ip directed-broadcast
!
interface Serial0
 ip address 80.65.91.86 255.255.255.252
 ip access-group 11 out
 no ip directed-broadcast
 encapsulation ppp
 no fair-queue
!
router igrp 1
 network 10.0.0.0
 network 80.0.0.0
!
ip default-gateway 80.65.91.85
ip name-server 195.222.32.10
ip classless
ip route 0.0.0.0 0.0.0.0 80.65.91.85
ip route 0.0.0.0 0.0.0.0 Serial0
access-list 112 permit ip 80.65.91.80 0.0.0.15 any
access-list 112 permit ip 10.40.0.0 0.0.0.255 any
!
line con 0
 exec-timeout 0 0
line vty 0 4
 password <removed>
 login
!
end


------------------ show controllers ------------------

QUICC Ethernet unit 0 using SCC1, Microcode ver 4
Current station address 00d0.58a3.b034, default address 00d0.58a3.b034
idb at 0x233F700, driver data structure at 0x233CFF8
SCC Registers:
General [GSMR]=0x0:0x1088003C, Protocol-specific [PSMR]=0x80A
Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x0002
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0xD555
Interrupt Registers:
Config [CICR]=0x00368461, Pending [CIPR]=0x00004004
Mask   [CIMR]=0xC8000012, In-srv  [CISR]=0x00000000
Command register [CR]=0x6C0
Port A [PADIR]=0x0000, [PAPAR]=0xCCC3
       [PAODR]=0x0000, [PADAT]=0x75FE
Port B [PBDIR]=0x00F13E, [PBPAR]=0x0010CE
       [PBODR]=0x000000, [PBDAT]=0x034ADD
Port C [PCDIR]=0x0002, [PCPAR]=0x0008
       [PCSO]=0x0C30,  [PCDAT]=0x07CC, [PCINT]=0x0000

SCC GENERAL PARAMETER RAM (at 0xFF00C00)
Rx BD Base [RBASE]=0x420, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0x490, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=1520
Rx State [RSTATE]=0x18000000, BD Ptr [RBPTR]=0x430
Tx State [TSTATE]=0x18000AE3, BD Ptr [TBPTR]=0x4A0

SCC ETHERNET PARAMETER RAM (at 0xFF00C30)
CRC Preset [C_PRES]=0xFFFFFFFF, Mask [C_MASK]=0xDEBB20E3
Errors: CRC [CRCEC]=0, Alignment [ALEC]=0, Discards [DISFC]=0
PAD Char [PADS]=0x0
Retry Limit [RET_LIM]=15, Count [RET_CNT]=15
Frame Lengths: [MAXFLR]=1518, [MINFLR]=64
Max DMA Lengths: [MAXD1]=1518, [MAXD2]=1518
Group Address Filter [GADDRn]=0000:0000:0000:0100
Indiv Address Filter [IADDRn]=0000:0000:0000:0000
Physical Address [PADDR1]=34B0.A358.D000
Last Address Set in Filter [TADDR]=CCCC.CC0C.0001
Persistence [P_Per]=0, Backoff Cnt [BOFF_CNT]=0
BD Pointers:
First Rx [RFBD]=0x0, First Tx [TFBD]=0x4A8, Last Tx [TLBD]=0x4A0

RX ring with 8 entries at 0xFF00420, Buffer size 1524
Rxhead = 0xFF00438 (3), Rxp = 0x233D020 (3)
00 pak=0x23435E4 buf=0x278F454 status=9000 pak_size=0
01 pak=0x2342A14 buf=0x278C54C status=9000 pak_size=0
02 pak=0x2342D74 buf=0x278D2BC status=9000 pak_size=0
03 pak=0x2343794 buf=0x278FB0C status=9000 pak_size=0
04 pak=0x2343434 buf=0x278ED9C status=9000 pak_size=0
05 pak=0x2343AF4 buf=0x279087C status=9000 pak_size=0
06 pak=0x2343944 buf=0x27901C4 status=9000 pak_size=0
07 pak=0x2342F24 buf=0x278D974 status=B000 pak_size=0

TX ring with 4 entries at 0xFF00490, tx_count = 0
tx_head = 0xFF004A8 (3), head_txp = 0x233D07C (3)
tx_tail = 0xFF004A8 (3), tail_txp = 0x233D07C (3)
00 pak=0x0000000 buf=0x0000000 status=0000 pak_size=0
01 pak=0x0000000 buf=0x0000000 status=0000 pak_size=0
02 pak=0x0000000 buf=0x0000000 status=0000 pak_size=0
03 pak=0x0000000 buf=0x0000000 status=2000 pak_size=0
0 missed datagrams, 0 overruns
0 transmitter underruns, 0 excessive collisions
0 single collisions, 0 multiple collisions
0 dma memory errors, 0 CRC errors

0 alignment errors, 0 runts, 0 giants
QUICC SCC specific errors:
0 buffer errors, 0 overflow errors
0 input aborts on late collisions
0 heartbeat failures, 0 cumulative deferred
0 throttles, 0 enables




QUICC Serial unit 0
idb at 0x2344364, driver data structure at 0x2346088
SCC Registers:
General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x0
Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x0006
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00368461, Pending [CIPR]=0x00004004
Mask   [CIMR]=0xC8000012, In-srv  [CISR]=0x00000000
Command register [CR]=0x6C0
Port A [PADIR]=0x0000, [PAPAR]=0xCCC3
       [PAODR]=0x0000, [PADAT]=0xF5FE
Port B [PBDIR]=0x00F13E, [PBPAR]=0x0010CE
       [PBODR]=0x000000, [PBDAT]=0x034ADD
Port C [PCDIR]=0x0002, [PCPAR]=0x0008
       [PCSO]=0x0C30,  [PCDAT]=0x07CC, [PCINT]=0x0000
DTE V.35 serial cable attached.

SCC GENERAL PARAMETER RAM (at 0xFF00F00)
Rx BD Base [RBASE]=0x580, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0x5C0, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=1524
Rx State [RSTATE]=0x18008240, BD Ptr [RBPTR]=0x5A8
Tx State [TSTATE]=0x0, BD Ptr [TBPTR]=0x5C0

SCC HDLC PARAMETER RAM (at 0xFF00F38)
CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0
Nonmatch Addr Cntr [NMARC]=0
Retry Count [RETRC]=0
Max Frame Length [MFLR]=1524
Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=65531
User-defined Address 0000/0000/0000/0000
User-defined Address Mask 0x0000


buffer size 1524
BRGC1=101B0, BRGC2=0, BRGC3=0, BRGC4=0
modem_signal_addr FF01566
MASK: DSR=1, DTR=2,RTS=8.CTS=400,DCD=800
txbrgc=FF015FC, rxbrgc=FF015FC
BRG [DTE]: rx_sicr_clk=7, tx_sicr_clk=6
BRG [DCE]: rx_sicr_clk=7, tx_sicr_clk=3
CLK SRC: sync=4000, async=4000
RX ring with 8 entries at 0xFF00580, Buffer size 1524
Rxhead = 0xFF005A8 (5), Rxp = 0x23460B8 (5)
00 pak=0x2386F34 buf=0x27B1484 status=9000 pak_size=0
01 pak=0x2386874 buf=0x2793E48 status=9000 pak_size=0
02 pak=0x2348FE4 buf=0x2793790 status=9000 pak_size=0
03 pak=0x2348C84 buf=0x2792A20 status=9000 pak_size=0
04 pak=0x23875F4 buf=0x27B2F64 status=9000 pak_size=0
05 pak=0x234A1D8 buf=0x2798178 status=9000 pak_size=0
06 pak=0x2386BD4 buf=0x27B0714 status=9000 pak_size=0
07 pak=0x234A028 buf=0x2797AC0 status=B000 pak_size=0

TX ring with 4 entries at 0xFF005C0, tx_count = 4
tx_head = 0xFF005C0 (0), head_txp = 0x2346100 (0)
tx_tail = 0xFF005C0 (0), tail_txp = 0x2346100 (0)
00 pak=0x235E7E4 buf=0x279A284 status=9C00 pak_size=14
01 pak=0x235E994 buf=0x279A3B0 status=9C00 pak_size=14
02 pak=0x235EB44 buf=0x279A4DC status=9C00 pak_size=14
03 pak=0x235EEA4 buf=0x279A734 status=BC00 pak_size=14
QUICC SCC specific errors:
1 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts


------------------ show stacks ------------------


Minimum process stacks:
 Free/Size   Name
  884/1000   c1000 LED
 1620/2000   Router Init
 2800/4000   Init
 1888/4000   Virtual Exec

Interrupt level stacks:
Level    Called Unused/Size  Name
  4        4044   2544/3000  CPIC interrupts
  7           0   2980/3000  Programmable Interval Timer

------------------ show interfaces ------------------


Ethernet0 is up, line protocol is up
  Hardware is QUICC Ethernet, address is 00d0.58a3.b034 (bia 00d0.58a3.b034)
  Internet address is 10.40.0.1/16
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
  Encapsulation ARPA, loopback not set, keepalive set (10 sec)
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Queueing strategy: fifo
  Output queue 0/40, 0 drops; input queue 0/75, 0 drops
  5 minute input rate 2000 bits/sec, 3 packets/sec
  5 minute output rate 1000 bits/sec, 3 packets/sec
     2028 packets input, 130867 bytes, 0 no buffer
     Received 73 broadcasts, 0 runts, 0 giants
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 input packets with dribble condition detected
     1629 packets output, 177919 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Serial0 is up, line protocol is down
  Hardware is QUICC Serial
  Internet address is 80.65.91.86/30
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255
  Encapsulation PPP, loopback not set, keepalive set (10 sec)
  LCP ACKsent
  Closed: ipcp, cdp
  Last input 00:00:00, output never, output hang never
  Last clearing of "show interface" counters never
  Queueing strategy: fifo
  Output queue 14/40, 0 drops; input queue 0/75, 0 drops
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     251 packets input, 5074 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants
     44 input errors, 0 CRC, 43 frame, 0 overrun, 0 ignored, 1 abort
     219 packets output, 3066 bytes, 0 underruns
     0 output errors, 0 collisions, 106 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
     DCD=up  DSR=up  DTR=up  RTS=down  CTS=down


------------------ show buffers ------------------


Buffer elements:
     486 in free list (500 max allowed)
     6952 hits, 0 misses, 0 created

Public buffer pools:
Small buffers, 104 bytes (total 50, permanent 50):
     37 in free list (20 min, 150 max allowed)
     1045 hits, 0 misses, 0 trims, 0 created
     0 failures (0 no memory)
Middle buffers, 600 bytes (total 25, permanent 25):
     23 in free list (10 min, 150 max allowed)
     1196 hits, 0 misses, 0 trims, 0 created
     0 failures (0 no memory)
Big buffers, 1524 bytes (total 50, permanent 50):
     50 in free list (5 min, 150 max allowed)
     69 hits, 0 misses, 0 trims, 0 created
     0 failures (0 no memory)
VeryBig buffers, 4520 bytes (total 0, permanent 0):
     0 in free list (0 min, 100 max allowed)
     0 hits, 0 misses, 0 trims, 0 created
     0 failures (0 no memory)
Large buffers, 5024 bytes (total 0, permanent 0):
     0 in free list (0 min, 10 max allowed)
     0 hits, 0 misses, 0 trims, 0 created
     0 failures (0 no memory)
Huge buffers, 18024 bytes (total 0, permanent 0):
     0 in free list (0 min, 4 max allowed)
     0 hits, 0 misses, 0 trims, 0 created
     0 failures (0 no memory)

Interface buffer pools:
Ethernet0 buffers, 1524 bytes (total 28, permanent 28):
     13 in free list (0 min, 28 max allowed)
     15 hits, 0 fallbacks
     7 max cache size, 6 in cache
Serial0 buffers, 1524 bytes (total 16, permanent 16):
     3 in free list (0 min, 16 max allowed)
     52 hits, 7 fallbacks
     4 max cache size, 0 in cache



------------------ show process memory ------------------


Total: 5253136, Used: 786352, Free: 4466784
 PID  TTY  Allocated      Freed    Holding    Getbufs    Retbufs Process
   0    0      24784        300     667600          0          0 *Init*
   0    0        388      19024        388          0          0 *Sched*
   0    0    1182976     409788        560     216700      27520 *Dead*
   1    2      57668      56528       5856          0          0 Virtual Exec
   2    0          0          0       2716          0          0 Check heaps
   3    0         92          0       2808          0          0 Pool Manager
   4    0        256        256       2716          0          0 Timers
   5    0        332          0       2968          0          0 ARP Input
   6    0         92          0       2808          0          0 SERIAL A'detect
   7    0        232          0       2948          0          0 Probe Input
   8    0         92          0       2808          0          0 RARP Input
   9    0        128        748       4844          0          0 IP Input
  10    0          0        748       2716          0          0 TCP Timer
  11    0      18136          0       6544          0          0 TCP Protocols
  12    0        568        284       3000          0          0 CDP Protocol
  13    0       8964       8012       3668          0          0 BOOTP Server
  14    0          0          0       2716          0          0 Asy FS Helper
  15    0          0          0       4716          0          0 IP Background
  16    0          0          0       2716          0          0 IP Cache Ager
  17    0        128          0       2868          0          0 Critical Bkgnd
  18    0       5524          0       2808          0          0 Net Background
  19    0        348        256       4808          0          0 Logger
  20    0        256        256       2716          0          0 TTY Background
  21    0          0          0       2716          0          0 Per-Second Jobs
  22    0          0          0       2716          0          0 Net Periodic
  23    0        184          0       2900          0          0 Net Input
  24    0          0        560       2716          0          0 Per-minute Jobs
  25    0        512        256       2972          0          0 CCP manager
  26    0          0          0       2716          0          0 PPP manager
  28    0      64900      56524      11092          0          0 Config Probe
  29    0      56812      56812       2716          0          0 Config Probe
  30    0          0          0       2716          0          0 IP-RT Background
  31    0        528          0      14472          0          0 IGRP Router
                                    786028 Total

------------------ show process cpu ------------------


CPU utilization for five seconds: 9%/6%; one minute: 13%; five minutes: 12%
 PID  Runtime(ms)  Invoked  uSecs    5Sec   1Min   5Min TTY Process
   1        2972       144  20638   2.62%  0.75%  0.16%   2 Virtual Exec
   2       31220       306 102026   0.00%  1.43%  1.50%   0 Check heaps
   3           0         1      0   0.00%  0.00%  0.00%   0 Pool Manager
   4           0         2      0   0.00%  0.00%  0.00%   0 Timers
   5          24        73    328   0.00%  0.00%  0.00%   0 ARP Input
   6           0         1      0   0.00%  0.00%  0.00%   0 SERIAL A'detect
   7           0         1      0   0.00%  0.00%  0.00%   0 Probe Input
   8           0         1      0   0.00%  0.00%  0.00%   0 RARP Input
   9        1712      2021    847   0.24%  0.06%  0.01%   0 IP Input
  10         484      1638    295   0.00%  0.03%  0.00%   0 TCP Timer
  11          12        13    923   0.00%  0.00%  0.00%   0 TCP Protocols
  12           8       211     37   0.00%  0.00%  0.00%   0 CDP Protocol
  13          36        23   1565   0.00%  0.00%  0.00%   0 BOOTP Server
  14           0         1      0   0.00%  0.00%  0.00%   0 Asy FS Helper
  15         416      2076    200   0.00%  0.00%  0.00%   0 IP Background
  16           0        34      0   0.00%  0.00%  0.00%   0 IP Cache Ager
  17           0         1      0   0.00%  0.00%  0.00%   0 Critical Bkgnd
  18           8       100     80   0.00%  0.00%  0.00%   0 Net Background
  19           4        13    307   0.00%  0.00%  0.00%   0 Logger
  20         132      1950     67   0.00%  0.00%  0.00%   0 TTY Background
  21          16      2039      7   0.00%  0.00%  0.00%   0 Per-Second Jobs
  22         404      2038    198   0.00%  0.00%  0.00%   0 Net Periodic
  23           4         1   4000   0.00%  0.00%  0.00%   0 Net Input
  24         984        34  28941   0.00%  0.02%  0.00%   0 Per-minute Jobs
  25           0         2      0   0.00%  0.00%  0.00%   0 CCP manager
  26          44       252    174   0.00%  0.00%  0.00%   0 PPP manager
  28          32        29   1103   0.00%  0.00%  0.00%   0 Config Probe
  29          24        28    857   0.00%  0.00%  0.00%   0 Config Probe
  30           0        34      0   0.00%  0.00%  0.00%   0 IP-RT Background
  31         296        25  11840   0.00%  0.01%  0.00%   0 IGRP Router

Tux The Killer
 
Odgovor na temu

markom
Marko Milivojević
Network Engineer
Google
Mountain View

Član broj: 18427
Poruke: 4227
*.lina.net

Sajt: https://markom.rs


+16 Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 12:28 - pre 240 meseci
Hm, na prvi pogled jedino što mi pada na pamet je da sa provajderom proveriš enkapsulaciju još jednom. Probaj "encapsulation hdlc" na Serial0 interfejsu, čisto probe radi.

Takođe, probaj "debug ppp negotiation", pa vidi šta se dešava.

Marko.

P.S. Broj grešaka na serijskom interfejsu je kanda sulud u odnosu na broj paketa. Uradi "clear counters" pa vidi da li se povećavaju greške. Ako primtetno rastu, ne bih se previše čudio što sve to ne radi.

 
Odgovor na temu

Gojko Vujovic
Amsterdam, NL

Administrator
Član broj: 1
Poruke: 13651



+165 Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 12:39 - pre 240 meseci
Nešto drugo meni nije jasno, dok vi rešavate problem line protokola.

Ti na eth0 koristiš interni opseg. Zašto pališ routing protokol na njemu? Gde ti je NAT?

Prvi sledeći ruter kada dobije 10.x source, ako je normalno konfigurisan, odbiće ti takve pakete i link neće raditi. Ako to ne uradi taj kod provajdera, neko na putu do destinacije sigurno hoće.

A da ne pričamo o access listi koja nema nikakvog smisla. Stavio si je na out a proveravaš i ulazno.. ako se kačiš na net, ovo ti nikako neće proraditi.

Zato postoje ljudi koji se bave profesionalno konfiguracijom rutera. Dovedeš ga na 2 sata, kažeš treba mi to to to i to, on namesti, ti platiš, svi srećni i zadovoljni.
 
Odgovor na temu

alex
Aleksandar Radulovic
Senior Software Engineer, Spotify
Stockholm, Sweden

Član broj: 71
Poruke: 2194
*.habil.is

Jabber: alex@a13x.info
ICQ: -1
Sajt: www.a13x.info


+1 Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 12:44 - pre 240 meseci
Gojko, a sta ako je provajder taj koji radi NAT za njega?
Alex: My favorite site is http://localhost/
R.J. Oppenheimer: "I am become death, destroyer of worlds" (1945 AD)
tweet.13x ||
linkedin.13x
 
Odgovor na temu

markom
Marko Milivojević
Network Engineer
Google
Mountain View

Član broj: 18427
Poruke: 4227
*.lina.net

Sajt: https://markom.rs


+16 Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 12:48 - pre 240 meseci
To je dobar komentar, ali onda verovatno ne bi imao interconnect subnet sa pravim opsegom, već bi verovatno bila nenumerisana point to point veza.

Marko.
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 12:59 - pre 240 meseci
evo javljam se...vidio sam kakav sam apsurd uradio sa access listom i grupom, izbrisao ssssssssssam ih, i izbrisao sam sam taj igrp.....cilj mi je da u shellu uradim ping na neki sajt.....ako proradi rjesavat cu ostalo...
Tux The Killer
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 13:03 - pre 240 meseci
eeee Gojko, kako bih ja bio sretan da ima takvih ljudi....to jesam pitao ISP. Ali znas ono:

Gospodine, kupite router koji kosta 500E kod nas i mi vam usput konfigurisemo router da radi.....ovako ako imas svoj router koji je bolje 5 puta onda nemas taj support...aka MONOPOL!
Tux The Killer
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 13:05 - pre 240 meseci
Code:
MEMO#show run
Building configuration...

Current configuration:
!
version 11.1
service config
service udp-small-servers
service tcp-small-servers
!
hostname MEMO
!
enable secret 5 xxxxxxx
enable password xxxxxxx
!
ip subnet-zero
ip address-pool local
!
interface Ethernet0
 ip address 10.40.0.1 255.255.0.0
 no ip directed-broadcast
!
interface Serial0
 ip address 80.65.91.86 255.255.255.252
 no ip directed-broadcast
 encapsulation ppp
 no fair-queue
!
ip default-gateway 80.65.91.85
ip name-server 195.222.32.10
ip classless
ip route 0.0.0.0 0.0.0.0 80.65.91.85
ip route 0.0.0.0 0.0.0.0 Serial0
!
line con 0
 exec-timeout 0 0
line vty 0 4
 password xxxxxxxxx
 login
!
end

Tux The Killer
 
Odgovor na temu

_tux_rulez
rabjorn speiler

Član broj: 5510
Poruke: 70
*.as54.ze.bih.net.ba.



Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 13:13 - pre 240 meseci
Sto se tice enkapsulacije...ISP mi je rekao da su prebacili na PPP, jer hdlc ocito nije radio :)
Tux The Killer
 
Odgovor na temu

Gojko Vujovic
Amsterdam, NL

Administrator
Član broj: 1
Poruke: 13651
Via: [es] mailing liste



+165 Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 13:18 - pre 240 meseci
alex, dobio je on javnu peer mrežu kako se vidi iz konfiguracije tako da stoji da ovo sa direktnim rutiranjem između javnog i privatnog opsega ne pije vodu.

tux, jesi li probao da debuguješ PPP i vidiš gde to puca?
I još jedno pitanje. Možeš li nam ovde poslati SVE parametre koje si dobio od provajdera. Dakle tačno kako su ti zapisali, izdiktirali, itd. Šta su rekli za enkapsulaciju, rutiranje, opsege koji su ti dodeljeni, itd itd. Pošto vidim da si po slobodnom nahođenju dizao IGRP, moguće je da si i ništo propustio da uradiš što je provajder tražio.

Doduše meni nije tačno jasno zašto se ti baviš dizanjem line protokola. Taj ISP ti prodaje internet, njihov CSU/DSU, neka podignu protokol. Oni bi trebalo da dovedu IP do tvog peer-a i na to da ti rutiraju adrese koje si dobio, a tvoj posao bi trebalo da bude posle ostalo setovanje (eth interfejsa, rutiranje u okviru tvoje mreže, itd).
 
Odgovor na temu

Gojko Vujovic
Amsterdam, NL

Administrator
Član broj: 1
Poruke: 13651
Via: [es] mailing liste



+165 Profil

icon Re: CISCO 1600 router+Leased Line problemi28.06.2004. u 13:21 - pre 240 meseci
Hm da pošto sam prethodni odgovor pisao preko maila, nisam uzeo u obzir tvoje prethodne tri poruke gde si već pojasnio nešto u vezi sa provajderom.

Ništa iščupaj serijski kablić, uključi debugging, resetuj countere, vrati kabl i gledaj šta debug kaže.
 
Odgovor na temu

[es] :: Enterprise Networking :: CISCO 1600 router+Leased Line problemi

Strane: 1 2 3 4

[ Pregleda: 15700 | Odgovora: 61 ] > FB > Twit

Postavi temu Odgovori

Navigacija
Lista poslednjih: 16, 32, 64, 128 poruka.