Zdravo.
Evo opet se, nakon dvije nedelje, javio isti problem.
Sada server mogu da ping-am, kada pokušam da se konektujem pomoću PUTTY-a dozvoli mi da unesem username, a kada unesem password zaglavi i na kraju nakon 10 minuta izbaci grešku o mrežnom time-out-u.
Konfigurisao sam iLO2 ali mi ni to ništa nije pomoglo.
Evo iLO2 screen-ova za vrijme dok je server zaglavljen:
Server sam morao da resetujem ručno jer ni pomoću iLO2 konzole nisam mogao.
Evo i dijelova nekih značajnih logova:
dmesg:
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie03]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C3] C3[C3])
ACPI: CPU2 (power states: C1[C1] C2[C3] C3[C3])
ACPI: CPU1 (power states: C1[C1] C2[C3] C3[C3])
ACPI: CPU3 (power states: C1[C1] C2[C3] C3[C3])
ACPI: Thermal Zone [THM0] (8 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S4 S5)
Initalizing network drop monitor service
Freeing unused kernel memory: 208k freed
Write protecting the kernel read-only data: 496k
GSI 17 sharing vector 0x5A and IRQ 17
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 90
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 90, io mem 0xf1df0000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 90
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 90, io base 0x00001000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
GSI 18 sharing vector 0x62 and IRQ 18
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 23 (level, low) -> IRQ 98
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 98, io base 0x00001020
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
GSI 19 sharing vector 0x6A and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 106
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 106, io base 0x00001040
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 98
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 98, io base 0x00001060
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:01:04.4[B] -> GSI 22 (level, low) -> IRQ 106
uhci_hcd 0000:01:04.4: UHCI Host Controller
uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 6
uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
uhci_hcd 0000:01:04.4: irq 106, io base 0x00003800
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
SCSI subsystem initialized
HP CISS Driver (v 3.6.20-RH3)
GSI 20 sharing vector 0x72 and IRQ 20
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 28 (level, low) -> IRQ 114
cciss0: <0x323a> at PCI 0000:04:00.0 IRQ 138 using DAC
blocks= 860051248 block_size= 512
heads= 255, sectors= 32, cylinders= 105399
blocks= 860051248 block_size= 512
heads= 255, sectors= 32, cylinders= 105399
cciss/c0d0: p1 p2
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.12
GSI 21 sharing vector 0x9A and IRQ 21
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 154
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
usb 6-1: new full speed USB device using uhci_hcd and address 2
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x1080 ctl 0x1088 bmdma 0x10a0 irq 154
ata2: SATA max UDMA/133 cmd 0x1090 ctl 0x1098 bmdma 0x10a8 irq 154
usb 6-1: configuration #1 chosen from 1 choice
input: HP Virtual Keyboard as /class/input/input0
input: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1
input: HP Virtual Keyboard as /class/input/input1
input: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1
usb 6-2: new full speed USB device using uhci_hcd and address 3
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.01: NODEV after polling detection
ata1.00: ATAPI: Optiarc DVD-ROM DDU820S, MH52, max UDMA/100
usb 6-2: configuration #1 chosen from 1 choice
hub 6-2:1.0: USB hub found
hub 6-2:1.0: 7 ports detected
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 4 SControl 300)
Vendor: Optiarc Model: DVD-ROM DDU820S Rev: MH52
Type: CD-ROM ANSI SCSI revision: 05
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised:
[email protected]
device-mapper: dm-raid45: initialized v0.2594l
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: dm-0: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 91095045
ext3_orphan_cleanup: deleting unreferenced inode 91095046
ext3_orphan_cleanup: deleting unreferenced inode 91095047
ext3_orphan_cleanup: deleting unreferenced inode 91095056
ext3_orphan_cleanup: deleting unreferenced inode 91095059
ext3_orphan_cleanup: deleting unreferenced inode 91095064
EXT3-fs: dm-0: 6 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
type=1404 audit(1265368482.149:2): selinux=0 auid=4294967295 ses=4294967295
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.9.3 (March 17, 2009)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem f4000000, IRQ 169, node addr 0025b3deeacc
ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 17 (level, low) -> IRQ 154
PCI: Setting latency timer of device 0000:02:00.1 to 64
eth1: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem f2000000, IRQ 154, node addr 0025b3deeace
GSI 22 sharing vector 0xA2 and IRQ 22
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 162
PCI: Setting latency timer of device 0000:03:00.0 to 64
eth2: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem f8000000, IRQ 162, node addr 0025b3deead0
GSI 23 sharing vector 0xAA and IRQ 23
ACPI: PCI Interrupt 0000:03:00.1[B] -> GSI 19 (level, low) -> IRQ 170
PCI: Setting latency timer of device 0000:03:00.1 to 64
eth3: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem f6000000, IRQ 170, node addr 0025b3deead2
Floppy drive(s): fd0 is 1.44M
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:01:04.2[B] -> GSI 22 (level, low) -> IRQ 106
input: PC Speaker as /class/input/input2
scsi 0:0:0:0: Attached scsi generic sg0 type 5
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
lp: driver loaded but no devices found
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
mtrr: type mismatch for e8000000,4000000 old: uncachable new: write-combining
ACPI: Power Button (FF) [PWRF]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on cciss/c0d0p1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 8159224k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:8159224k
IA-32 Microcode Update Driver: v1.14a <
[email protected]>
bnx2: eth0: using MSIX
ADDRCONF(NETDEV_UP): eth0: link is not ready
bnx2: eth0 NIC Copper Link is Up, 100 Mbps full duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
bnx2: eth1: using MSIX
ADDRCONF(NETDEV_UP): eth1: link is not ready
bnx2: eth1 NIC Copper Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
eth0: no IPv6 routers present
Installing knfsd (copyright (C) 1996
[email protected]).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
eth1: no IPv6 routers present
mtrr: type mismatch for e8000000,4000000 old: uncachable new: write-combining
messages:
Feb 2 12:18:21 ucmserver NXSERVER-3.4.0-8[21312]: Session with id: A9A3E388E357A5F96D95FB490CAE9693: restored 'NXShell::handler_session_start'
Feb 2 12:18:22 ucmserver gconfd (oracle-21318): starting (version 2.14.0), pid 21318 user 'oracle'
Feb 2 12:18:22 ucmserver gconfd (oracle-21318): Resolved address "xml:readonly:/etc/gconf/gconf.xml.mandatory" to a read-only configuration source at position 0
Feb 2 12:18:22 ucmserver gconfd (oracle-21318): Resolved address "xml:readwrite:/home/oracle/.gconf" to a writable configuration source at position 1
Feb 2 12:18:22 ucmserver gconfd (oracle-21318): Resolved address "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only configuration source at position 2
Feb 5 12:15:09 ucmserver syslogd 1.4.1: restart.
Feb 5 12:15:09 ucmserver kernel: klogd 1.4.1, log source = /proc/kmsg started.
Feb 5 12:15:09 ucmserver kernel: Linux version 2.6.18-164.el5 (
[email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-46)) #1 SMP Thu Sep 3 03:28:30 EDT 2009
Feb 5 12:15:09 ucmserver kernel: Command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Feb 5 12:15:09 ucmserver kernel: BIOS-provided physical RAM map:
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 0000000000010000 - 000000000009f400 (usable)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 0000000000100000 - 00000000df63f000 (usable)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 00000000df63f000 - 00000000df64c000 (ACPI data)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 00000000df64c000 - 00000000df64d000 (usable)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 00000000df64d000 - 00000000e4000000 (reserved)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 00000000fec00000 - 00000000fee10000 (reserved)
Feb 5 12:15:09 ucmserver kernel: BIOS-e820: 0000000100000000 - 000000019ffff000 (usable)
Feb 5 12:15:09 ucmserver kernel: DMI 2.6 present.
Feb 5 12:15:09 ucmserver rpc.statd[2735]: Version 1.0.9 Starting
Feb 5 12:15:09 ucmserver kernel: SRAT: PXM 0 -> APIC 0 -> Node 0
Feb 5 12:15:09 ucmserver kernel: SRAT: PXM 0 -> APIC 2 -> Node 0
Feb 5 12:15:09 ucmserver kernel: SRAT: PXM 0 -> APIC 4 -> Node 0
Feb 5 12:15:09 ucmserver kernel: SRAT: PXM 0 -> APIC 6 -> Node 0
Feb 5 12:15:09 ucmserver kernel: SRAT: Node 0 PXM 0 0-e0000000
Feb 5 12:15:09 ucmserver kernel: SRAT: Node 0 PXM 0 0-1a0000000
Feb 5 12:15:09 ucmserver kernel: Bootmem setup node 0 0000000000000000-000000019ffff000
Feb 5 12:15:09 ucmserver kernel: Memory for crash kernel (0x0 to 0x0) notwithin permissible range
Feb 5 12:15:09 ucmserver kernel: disabling kdump
Feb 5 12:15:10 ucmserver rpc.statd[2735]: statd running as root. chown /var/lib/nfs/statd/sm to choose different user
Feb 5 12:15:10 ucmserver kernel: ACPI: PM-Timer IO Port: 0x908
Feb 5 12:15:10 ucmserver kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Feb 5 12:15:10 ucmserver kernel: Processor #0 7:10 APIC version 21
...
Feb 5 12:15:10 ucmserver kernel: Setting APIC routing to physical flat
Feb 5 12:15:10 ucmserver kernel: ACPI: HPET id: 0x8086a201 base: 0xfed00000
Feb 5 12:15:10 ucmserver kernel: Using ACPI (MADT) for SMP configuration information
Feb 5 12:15:10 ucmserver kernel: Nosave address range: 000000000009f000 - 00000000000a0000
Feb 5 12:15:10 ucmserver pcscd: hotplug_libusb.c:402:HPEstablishUSBNotifications() Driver ifd-egate.bundle does not support IFD_GENERATE_HOTPLUG. Using active polling instead.
Feb 5 12:15:10 ucmserver kernel: Nosave address range: 00000000000a0000 - 00000000000f0000
Feb 5 12:15:11 ucmserver pcscd: hotplug_libusb.c:411:HPEstablishUSBNotifications() Polling forced every 1 second(s)
...
Feb 5 12:15:11 ucmserver kernel: Security Framework v1.0.0 initialized
Feb 5 12:15:11 ucmserver kernel: SELinux: Initializing.
Feb 5 12:15:11 ucmserver kernel: selinux_register_security: Registering secondary module capability
Feb 5 12:15:11 ucmserver kernel: Capability LSM initialized as secondary
Feb 5 12:15:11 ucmserver kernel: Mount-cache hash table entries: 256
Feb 5 12:15:11 ucmserver kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Feb 5 12:15:11 ucmserver kernel: CPU: L2 cache: 256K
Feb 5 12:15:11 ucmserver kernel: CPU: L3 cache: 4096K
Feb 5 12:15:11 ucmserver kernel: CPU 0/0 -> Node 0
Feb 5 12:15:11 ucmserver kernel: using mwait in idle threads.
Feb 5 12:15:11 ucmserver kernel: CPU: Physical Processor ID: 0
Feb 5 12:15:11 ucmserver kernel: CPU: Processor Core ID: 0
Feb 5 12:15:11 ucmserver kernel: CPU0: Thermal monitoring enabled (TM1)
Feb 5 12:15:11 ucmserver kernel: SMP alternatives: switching to UP code
Feb 5 12:15:11 ucmserver kernel: ACPI: Core revision 20060707
Feb 5 12:15:11 ucmserver kernel: Using local APIC timer interrupts.
Feb 5 12:15:11 ucmserver kernel: result 8333813
Feb 5 12:15:11 ucmserver kernel: Detected 8.333 MHz APIC timer.
Feb 5 12:15:11 ucmserver kernel: SMP alternatives: switching to SMP code
Feb 5 12:15:12 ucmserver kernel: Booting processor 1/4 APIC 0x4
Feb 5 12:15:12 ucmserver kernel: Initializing CPU#1
Feb 5 12:15:12 ucmserver kernel: Calibrating delay using timer specific routine.. 4000.05 BogoMIPS (lpj=2000028)
Feb 5 12:15:12 ucmserver kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Feb 5 12:15:12 ucmserver kernel: CPU: L2 cache: 256K
Feb 5 12:15:12 ucmserver kernel: CPU: L3 cache: 4096K
Feb 5 12:15:12 ucmserver kernel: CPU 1/4 -> Node 0
Feb 5 12:15:12 ucmserver kernel: CPU: Physical Processor ID: 0
Feb 5 12:15:12 ucmserver kernel: CPU: Processor Core ID: 2
Feb 5 12:15:12 ucmserver kernel: CPU1: Thermal monitoring enabled (TM1)
Feb 5 12:15:12 ucmserver kernel: Intel(R) Xeon(R) CPU E5504 @ 2.00GHz stepping 05
Feb 5 12:15:12 ucmserver kernel: SMP alternatives: switching to SMP code
Feb 5 12:15:12 ucmserver kernel: Booting processor 2/4 APIC 0x2
Feb 5 12:15:12 ucmserver kernel: Initializing CPU#2
Feb 5 12:15:12 ucmserver kernel: Calibrating delay using timer specific routine.. 4000.23 BogoMIPS (lpj=2000117)
Feb 5 12:15:12 ucmserver kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Feb 5 12:15:12 ucmserver kernel: CPU: L2 cache: 256K
Feb 5 12:15:12 ucmserver kernel: CPU: L3 cache: 4096K
Feb 5 12:15:12 ucmserver kernel: CPU 2/2 -> Node 0
...
Feb 5 12:15:13 ucmserver kernel: DMAR:RMRR base: 0x00000000df7fc000 end: 0x00000000df7fdfff
Feb 5 12:15:13 ucmserver kernel: DMAR:RMRR base: 0x00000000df7f5000 end: 0x00000000df7fafff
Feb 5 12:15:13 ucmserver kernel: DMAR:RMRR base: 0x00000000df64e000 end: 0x00000000df64ffff
Feb 5 12:15:13 ucmserver kernel: DMAR:Unknown DMAR structure type
Feb 5 12:15:13 ucmserver kernel: PCI-GART: No AMD northbridge found.
Feb 5 12:15:13 ucmserver kernel: pnp: 00:01: ioport range 0x408-0x40f has been reserved
Feb 5 12:15:13 ucmserver kernel: pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved
Feb 5 12:15:13 ucmserver kernel: pnp: 00:01: ioport range 0x700-0x71f has been reserved
Feb 5 12:15:13 ucmserver kernel: PCI: Bridge: 0000:00:01.0
Feb 5 12:15:13 ucmserver kernel: IO window: 4000-4fff
Feb 5 12:15:13 ucmserver kernel: MEM window: fbb00000-fbffffff
Feb 5 12:15:13 ucmserver kernel: PREFETCH window 0x00000000e6000000-0x00000000e60fffff
Feb 5 12:15:13 ucmserver kernel: PCI: Bridge: 0000:00:02.0
...
Feb 5 12:15:13 ucmserver kernel: PCI: Bridge: 0000:00:02.0
Feb 5 12:15:13 ucmserver kernel: IO window: disabled.
Feb 5 12:15:13 ucmserver kernel: MEM window: disabled.
Feb 5 12:15:13 ucmserver kernel: PREFETCH window: disabled.
Feb 5 12:15:13 ucmserver kernel: PCI: Bridge: 0000:00:03.0
Feb 5 12:15:13 ucmserver kernel: IO window: disabled.
Feb 5 12:15:13 ucmserver kernel: MEM window: disabled.
Feb 5 12:15:13 ucmserver kernel: PREFETCH window: disabled.
Feb 5 12:15:13 ucmserver kernel: PCI: Bridge: 0000:00:04.0
Feb 5 12:15:13 ucmserver kernel: IO window: disabled.
Feb 5 12:15:13 ucmserver kernel: MEM window: disabled.
Feb 5 12:15:13 ucmserver kernel: PREFETCH window: disabled.
Feb 5 12:15:13 ucmserver kernel: PCI: Bridge: 0000:00:05.0
Feb 5 12:15:13 ucmserver kernel: IO window: disabled.
Feb 5 12:15:13 ucmserver kernel: MEM window: disabled.
Feb 5 12:15:14 ucmserver kernel: PREFETCH window: disabled.
Feb 5 12:15:14 ucmserver kernel: PCI: Bridge: 0000:00:06.0
Feb 5 12:15:14 ucmserver kernel: IO window: disabled.
Feb 5 12:15:14 ucmserver kernel: MEM window: disabled.
Feb 5 12:15:14 ucmserver kernel: PREFETCH window: disabled.
Feb 5 12:15:14 ucmserver kernel: PCI: Bridge: 0000:00:07.0
...
Feb 5 12:15:20 ucmserver avahi-daemon[3154]: Found user 'avahi' (UID 70) and group 'avahi' (GID 70).
Feb 5 12:15:20 ucmserver kernel: EXT3-fs: write access will be enabled during recovery.
Feb 5 12:15:20 ucmserver avahi-daemon[3154]: Successfully dropped root privileges.
Feb 5 12:15:20 ucmserver kernel: kjournald starting. Commit interval 5 seconds
Feb 5 12:15:20 ucmserver avahi-daemon[3154]: avahi-daemon 0.6.16 starting up.
Feb 5 12:15:20 ucmserver kernel: EXT3-fs: dm-0: orphan cleanup on readonly fs
Feb 5 12:15:20 ucmserver avahi-daemon[3154]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns!
Feb 5 12:15:20 ucmserver avahi-daemon[3154]: Successfully called chroot().
Feb 5 12:15:20 ucmserver avahi-daemon[3154]: Successfully dropped remaining capabilities.
...
Feb 5 12:15:39 ucmserver smartd[3485]: smartd version 5.38 [x86_64-redhat-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Feb 5 12:15:39 ucmserver smartd[3485]: Home page is
http://smartmontools.sourceforge.net/
Feb 5 12:15:39 ucmserver smartd[3485]: Opened configuration file /etc/smartd.conf
Feb 5 12:15:39 ucmserver smartd[3485]: Configuration file /etc/smartd.conf was parsed, found DEVICESCAN, scanning devices
Feb 5 12:15:39 ucmserver smartd[3485]: Problem creating device name scan list
Feb 5 12:15:39 ucmserver smartd[3485]: Problem creating device name scan list
Feb 5 12:15:39 ucmserver smartd[3485]: In the system's table of devices NO devices found to scan
Feb 5 12:15:39 ucmserver smartd[3485]: Monitoring 0 ATA and 0 SCSI devices
Feb 5 12:15:39 ucmserver smartd[3487]: smartd has fork()ed into background mode. New PID=3487.
Feb 5 12:15:40 ucmserver pcscd: winscard.c:304:SCardConnect() Reader E-Gate 0 0 Not Found
Feb 5 12:15:40 ucmserver last message repeated 3 times
Feb 5 12:15:42 ucmserver kernel: mtrr: type mismatch for e8000000,4000000 old: uncachable new: write-combining
Zašto OS vidi samo 5GB RAM-a?
free -g
total used free shared buffers cached
Mem: 5 0 4 0 0 0
-/+ buffers/cache: 0 5
Swap: 7 0 7
Kad je:
cat /proc/meminfo |grep -i memtotal
MemTotal: 6103680 kB
[Ovu poruku je menjao suadhm dana 05.02.2010. u 16:04 GMT+1]