Navigacija
Lista poslednjih: 16, 32, 64, 128 poruka.

senao 2611CB3 plus (deluxe) firmware ugrade problem?

[es] :: Wireless :: senao 2611CB3 plus (deluxe) firmware ugrade problem?

[ Pregleda: 7534 | Odgovora: 4 ] > FB > Twit

Postavi temu Odgovori

Autor

Pretraga teme: Traži
Markiranje Štampanje RSS

OSCAR

Član broj: 3194
Poruke: 10
*.adsl.highway.telekom.at.



Profil

icon senao 2611CB3 plus (deluxe) firmware ugrade problem?09.01.2006. u 21:17 - pre 195 meseci
Imam AP senao 2611CB3 plus (deluxe) austrijske firme "Wavenet" sa njihovim softverom ver. 2.0.0.
Aktualna adresa je 192.168.1.99 (koja je default - nakon reseta)
Pokusao sam unijeti orginalni senao firmware fm 200 (ver. 2.0.0)
Nakon upgradea trebala bi default adresa biti 192.168.1.1 i trebao bi nestati logo "Wavenet".
Medjutim sve ostaje isto!
Ima li neka procedura kojom bi se mogao unijet originalni senao softver?

Hvala na pomoci!
 
Odgovor na temu

BEZIMENI
Dejan Djedovic
BALKAN

Član broj: 23574
Poruke: 113
195.178.58.*

Sajt: www.futsalbalkan.com


Profil

icon Re: senao 2611CB3 plus (deluxe) firmware ugrade problem?20.01.2006. u 21:38 - pre 194 meseci
imas na senaovom sajtu kompletno uputstvo za flesovanje
http://www.senao.com/english/co/home.asp
 
Odgovor na temu

skydiver021

Član broj: 21898
Poruke: 107
*.zig.nsinfo.co.yu.



Profil

icon Re: senao 2611CB3 plus (deluxe) firmware ugrade problem?24.01.2006. u 13:55 - pre 194 meseci
Evo linka za download flash-a i uputstvo

http://www.senao.com.tw/englis...4013/2611cb3plusDLX-frm200.zip

Nadam se da si radio po ovom uputstvu.

2611CB3 PLUS (Deluxe) Firmware Upgrade Guide
Firmware Version: 2.0.0
----------------------------------------------

*************************************************************************************
WARNING: 2611CB3 PLUS & 2611CB3 PLUS (Deluxe) firmware are NOT interchangeable.
Make sure that you upgrade the correct firmware. Refer to the bottom
of the device for the model number.

*************************************************************************************

* Note down the current version of your firmware. Click on the "System" on the left menu bar,
and then verify "Bridge Firmware", "WLAN Primary Firmware" & "WALN Secondary Firmware"

Follow the steps below to upgrade the firmware.

You must reset the hardware to the factory default settings before you begin
the upgrade process.

1. Unplug the device, hold down the reset button, and then plug the power back in.
Notice that the LAN LED is flashing. Release the reset button after 5 seconds.
The device will then reboot into its default configuration (192.168.1.1)
Note: This step is mandatory and will reset the device to its factory
default settings. (All previous settings will be lost.)

2. Change your computer's IP address and subnet mask to the following:
IP Address: 192.168.1.10
Subnet mask: 255.255.255.0

3. Successfully Ping 192.168.1.1

4. Launch the web-browser and connect to the device using its default IP address:
http://192.168.1.1

5. To Login, leave the username and password fields blank. Click on the OK button.

6. Click on "Admin" on the left menu bar, and then click on the "Switch" button to
switch to AP mode.

7. Once the switch has been completed, refresh the page.

8. Extract the firmware folder and then double click on "Do1.bat". Watch the LAN
& WLAN LEDs flash for a few seconds. It will then stay lit.

9. Unplug the device and then plug the power back in. Wait for 10 seconds.

10. Successfully Ping 192.168.1.1

11. Double click on "Do2.bat".
a) If your WLAN Primary firmware was less than 1.0 you will notice both the
LAN & WLAN LEDs flashing. Then the LAN LED will stay lit.
b) If your WLAN Primary firmware was 1.0 or greater, you will notice that only
the LAN LED is flashing. Then the LAN LED will stay lit.

12. Unplug the device, hold down the reset button, and then plug the power back in.
Notice that the LAN LED is flashing. Release the reset button after 5 seconds.
The device will then reboot into its default configuration (192.168.1.1)

* Note: This step is mandatory and will reset the device to its factory
default settings. (All previous settings will be lost.)

13. Successfully Ping 192.168.1.1

14. Launch the web-browser and connect to the device using its default IP address:
http://192.168.1.1

15. To Login, leave the username and password fields blank. Click on the OK button.

16. Click on the "System" on the left menu bar, and then verify "Bridge Firmware".
This should display the following:
AP Firmware: 2.0.0
WLAN Primary Firmware: 1.1.1
WLAN Secondary firmware: 1.8.0
WLAN Tertiary firmware: 1.3.8

Firmware Upgrade Complete.

Upgrade Guide Last Updated: 01/11/2005
 
Odgovor na temu

OSCAR

Član broj: 3194
Poruke: 10
*.adsl.highway.telekom.at.



Profil

icon Re: senao 2611CB3 plus (deluxe) firmware ugrade problem?28.01.2006. u 19:27 - pre 194 meseci
"http://www.senao.com.tw/englis...4013/2611cb3plusDLX-frm200.zip

Nadam se da si radio po ovom uputstvu.

2611CB3 PLUS (Deluxe) Firmware Upgrade Guide
Firmware Version: 2.0.0"


Radio sam sve po ovom istom uputstvu jedino
se u tacki 3. nakon reseta ne moze se pingovati na 192.168.1.1 nego na 192.168.1.99 jer je to adresa AP-a nakon reseta.
Postoji li kakv nacin da se dobije adresa 192.168.1.1 nakon reseta?
 
Odgovor na temu

Marcony
Network security inzenjer
Beograd

Član broj: 10486
Poruke: 1843
*.bg.wifi.vline.verat.net.



+17 Profil

icon Re: senao 2611CB3 plus (deluxe) firmware ugrade problem?07.02.2006. u 20:08 - pre 194 meseci
Takodje sam radio sve po uputstvu, medjutim od 10-og koraka uredjaj vise ne reaguje.
Flash-ovao sam uredjaj jer je prestao da funkcionise normalno. Mogao sam da ga ping-ujem preko LAN-a, i moglo mu se pristupiti preko web browser-a. Pojavi se prozor u kome trazi user i pass i kada se upise odgovarajuca kombinacija prikaze: "404 not found".

Pomislio sam da se izbrisao software, pa sam ga flash-ovao. Medjutim posle prvog flash-ovanja vise uopste ne moze da mu se pristupi.

Ima li kakvog resenja?

[Ovu poruku je menjao Marcony dana 08.02.2006. u 01:33 GMT+1]
YU2MP
 
Odgovor na temu

[es] :: Wireless :: senao 2611CB3 plus (deluxe) firmware ugrade problem?

[ Pregleda: 7534 | Odgovora: 4 ] > FB > Twit

Postavi temu Odgovori

Navigacija
Lista poslednjih: 16, 32, 64, 128 poruka.